manualshive.com logo in svg

Gestetner G060, Руководство по обслуживанию

Поделиться
Скачать
Gestetner G060 Скачать руководство пользователя страница 954

 Copyright

 

 2003 RICOH Corporation.  All rights reserved.

 

 

TECHNICAL SERVICE BULLETIN 

 
 

 

BULLETIN NUMBER:  G060/G570 – 021  

01/31/2003 

APPLICABLE MODEL:   
    GESTETNER – DSC38/DSc38S 
    RICOH – AP3800C/AP3800CMF 
    SAVIN – SLP38C/SLP38cS

 

 
 

SUBJECT:  BCU BOARD & DRIVE UNIT – K DEVELOPMENT

 

 

GENERAL: 

A fusing clutch has been added to the black development drive unit (P/N G0771100). This change 
maximizes the life of the fusing unit and oil supply unit. For this modification, the BCU board has also 
been changed. For details of these changes please see TSB G060/G570 – 020. The following parts 
updates are being issued for all G060 Parts Catalogs. Please update you parts catalog with the following 
information. 
 
 

 REFERENCE 

OLD PART NO. 

NEW PART NO. 

DESCRIPTION 

QTY  INT  PAGE  ITEM

G0775061 G0775067 

BCU 

Board 

1 

1 

85 

* 

G0601100 

G0771100 

Drive Unit – K Development 

1 

1 

57 

4 

 
 
 

UNITS AFFECTED: 

All G060 printers manufactured after the serial numbers listed below will have the new style Fusing Clutch 
and BCU Board installed during production. 
 

MODEL NAME 

SERIAL NUMBER 

Gestetner DSC38 

P6011100001 

Ricoh AP3800C 

P6011100001 

Savin SLP38C 

P6011100001 

 
 

INTERCHANGEABILITY CHART: 

0 

OLD and NEW parts can be used in both OLD and    
NEW machines. 

2 

NEW parts CAN NOT be used in OLD machines.               
OLD parts can be used in OLD and NEW machines. 

1 

NEW parts can be used in OLD and NEW machines. 
OLD parts CAN NOT be used in NEW machines. 

3 

OLD parts CAN NOT be used in NEW machines.               
NEW parts CAN NOT be used in OLD machines. 

3/S 

Must be installed as a set on units manufactured prior to the S/N cut-in. On units manufactured after the S/N cut-in or 
previously modified, use the new part numbers individually. 

 
 
 

 Not

e: Thi
s c

opy i

s i

ntended as a 

m

ast

er ori

ginal
 

   

    

    

 f

or reproduct

ion o

f addi

tion

al

 bul
le

tin

s. 

    

„

  

PA
R

T

S

 

 

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды