Gestetner G060 Скачать руководство пользователя страница 524

Страница: 524 / 1106

SC TABLE

G570 4-42 SM

SC 851

IEEE1394
interface error

The 1394 interface is
unusable.

•

Defective IEEE1394

•

Defective controller.

1. Turn the main switch off and on.
2. Replace the IEEE1394 interface

board.

3. Replace the controller.

SC 860

HDD:
Initialization error

The controller detects that
the hard disk fails.

•

HDD not initialized

•

Defective HDD

1. Turn the main switch off and on.
2. Reformat the HDD.
3. Replace the HDD.

SC 861

HDD: Reboot
error

The HDD does not become
ready within 30 seconds
after the power is supplied
to the HDD.

•

Loose connection

•

Defective cables

•

Defective HDD

•

Defective controller

1. Turn the main switch off and on.
2. Check the connection between the

HDD and controller.

3. Check and replace the cables.
4. Replace the HDD.
5. Replace the controller.

SC 863

HDD: Read error The data stored in the HDD

cannot be read correctly.

•

Defective HDD

•

Defective controller

1. Turn the main switch off and on.
2. Replace the HDD.
3. Replace the controller.

SC 864

HDD: CRC error

While reading data from the
HDD or storing data in the
HDD, data transmission
fails.

•

Defective HDD

1. Turn the main switch off and on.
2. Replace the HDD.

SC 865

HDD: Access
error

An error is detected while
operating the HDD.

•

Defective HDD

1. Turn the main switch off and on.
2. Replace the HDD.

SC 900

Electric counter
error

Abnormal data is stored in
the counters.

•

Defective NVRAM

•

Defective controller

1. Turn the main switch off and on.
2. Check the connection between the

NVRAM and controller.

3. Replace the NVRAM.
4. Replace the controller.

SC 990

Software
performance
error

The software makes an
unexpected operation.

•

Defective software

•

Defective controller

•

Software error

1. Turn the main switch off and on.
2. Reinstall the controller and/or engine

main firmware.

3. See

NOTE 1 at the end of the SC

table

Rev. 09/2003

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание G060

Отзывы:

Бренды по названию

Популярные бренды

Gestetner G060, Руководство по обслуживанию

Результаты поиска

Содержание G060

Отзывы:

Бренды по названию

Популярные бренды