manualshive.com logo in svg

Gestetner G060, Руководство по обслуживанию

Поделиться
Скачать
Gestetner G060 Скачать руководство пользователя страница 210

PRINTER ENGINE SERVICE MODE

G060

5-42

SM

7

Mode No.

(Class 1, 2, and 3)

Function / [ Setting ]

Displays the number of revolutions of motors or clutches for each current maintenance
unit.
[ 0 to 9999999 / 0 / 1 revolution/step ]
When a unit is replaced, the machine automatically detects that the new unit is installed.
Then, the current PM counter value is automatically moved to the PM Counter - Previous
(SP7-906-10 to 20) and is reset to “0”. The total number of revolutions made with the last
unit replaced can be checked with SP7-906-10 to 20.

17

R:PCU [K]

Target Revolution: 275338

18

R:PCU [Y]

Target Revolution: 295907

19

R:PCU [M]

Target Revolution: 295907

20

R:PCU [C]

Target Revolution: 295907

21

R:Dev. [K]

Target Revolution: 1076103

22

R:Dev. [Y]

Target Revolution: 1173387

23

R:Dev. [M]

Target Revolution: 1173387

24

R:Dev. [C]

Target Revolution: 1173387

25

R:Oil Supply

Target Revolution: 1861000

26

R:Fusing

Target Revolution: 9303000

27

R:Transfer

Target Revolution: 5163000

28

S:Waste Toner

29

S:Toner [K]

30

S:Toner [Y]

31

S:Toner [M]

32

S:Toner [C]

Displays the number of sheets printed until the
waste toner bottle becomes full or toner runs out.
[ 0 to 9999999 / - / 1 sheet/step ]

33

TonerSupply[K]

34

TonerSupply[Y]

35

TonerSupply[M]

803

36

TonerSupply[C]

*

Displays the total operating time for the toner
attraction pump.
[ 0 to 9999999 / - / 1 s/step ]

[PM Clear] PM Counter Clear
(Unit, [Color])
Dev.: Development Unit, PF: Paper Feed Rollers, Transfer: Transfer Unit

1

PCU [K]

2

PCU [Y]

3

PCU [M]

4

PCU [C]

5

Dev.  [K]

6

Dev. [Y]

7

Dev.  [M]

8

Dev.  [C]

9

Oil Supply

10

PF By-pass

11

PF Tray 1

12

PF Tray 2

13

PF Tray 3/LCT

14

PF Tray 4

15

Fusing

16

Transfer

804

50

All

*

Clears the PM counter.
Press the Enter key after the machine asks
“Execute?”.
When a unit is replaced, the machine
automatically detects that the new unit is installed.
Then, the current PM counter value is
automatically moved to the b PM Counter -
Previous (SP7-906-1 to 25) and is reset to “0”.
NOTE: The LCT is counted as the 3rd feed
station.

[SC/Jam Clear] SC/Jam Counter Clear

807

1

SC/Jam Clear

*

P

Clears the counters related to SC codes and
paper jams.

[Counter Clear]

808

1

Counter Clear

*

P

Clears all counters.
See NOTE 1 after the SP table for a list of
settings cleared.

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды