manualshive.com logo in svg

Gestetner G060, Руководство по обслуживанию

Поделиться
Скачать
Gestetner G060 Скачать руководство пользователя страница 597

Copie

r

F

eat

u

re

E

x

pa

nde

r

G

570

COPY SP MODE

SM

5-59

G570

7

Mode No.

(Class 1, 2, and 3)

Function / [ Setting ]

[PM Counter]
(Sheets or Rotations, Unit, [Color])
Dev.: Development Unit, PF: Paper Feed Rollers, Oil Supply: Oil Supply Unit, Fusing:
Fusing Unit, Transfer: Transfer Unit

1

S:PCU [K]

2

S:PCU [Y]

3

S:PCU [M]

4

S:PCU [C]

5

S:Dev. [K]

6

S:Dev. [Y]

7

S:Dev. [M]

8

S:Dev. [C]

9

S:Oil Supply

10

PF By-pass

11

PF Tray 1

12

PF Tray 2

13

PF Tray 3/LCT

14

PF Tray 4

15

S:Fusing

16

S:Transfer

*

BCU

Displays the number of sheets printed for each
current maintenance unit.
[ 0 to 9999999 / 0 / 1 sheet/step ]

PM counters click up based on the number of A4
(LT) LEF size sheets printed. Therefore, the A3
(DLT) Double Count is activated. The Double
Count cannot be deactivated.

When a unit is replaced, the machine
automatically detects that the new unit is installed.
Then, the current PM counter value is
automatically moved to the PM Counter - Previous
(SP7-906-1 to 9) and is reset to “0”.
The total number of sheets printed with the last
unit replaced can be checked with SP7-906-1 to 9.
NOTE: The LCT is counted as the 3rd feed

station.

Displays the number of revolutions of motors or clutches for each current maintenance
unit.
[ 0 to 9999999 / 0 / 1 revolution/step ]
When a unit is replaced, the machine automatically detects that the new unit is installed.
Then, the current PM counter value is automatically moved to the PM Counter - Previous
(SP7-906-10 to 20) and is reset to “0”. The total number of revolutions made with the last
unit replaced can be checked with SP7-906-10 to 20.

17

R:PCU [K]

Target Revolution: 550675

18

R:PCU [Y]

Target Revolution: 591813

19

R:PCU [M]

Target Revolution: 591813

20

R:PCU [C]

Target Revolution: 591813

21

R:Dev. [K]

Target Revolution: 1076103

22

R:Dev. [Y]

Target Revolution: 1173387

23

R:Dev. [M]

Target Revolution: 1173387

24

R:Dev. [C]

Target Revolution: 1173387

25

R:Oil Supply

Target Revolution: 1861000

26

R:Fusing

Target Revolution: 9303000

27

R:Transfer

Target Revolution: 5163000

28

S:Waste Toner

29

S:Toner [K]

30

S:Toner [Y]

31

S:Toner [M]

32

S:Toner [C]

Displays the number of sheets printed until the
waste toner bottle becomes full or toner runs out.
[ 0 to 9999999 / - / 1 sheet/step ]

33

TonerSupply[K]

34

TonerSupply[Y]

35

TonerSupply[M]

803

36

TonerSupply[C]

*

BCU

Displays the total operating time for the toner
attraction pump.
[ 0 to 9999999 / - / 1 s/step ]

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды