Gestetner G060 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 1106

Gestetner G060 Скачать руководство пользователя страница 138

SC TABLE

G060 4-24

SM

SC No.

Item

Definition

Possible Cause

Related

SCs

Troubleshooting Procedure

Type

SC 621

Finisher/mailbox

communication

error

SC 622

Bank

communication

error

•

Cable problems

•

BCU problems

•

PSU problems in the
machine

•

Main board problems
in the peripherals

1. Turn the main switch off and on.
2. Check if the cables of peripherals are

properly connected.

3. Replace the PSU if no power is

supplied to peripherals.

4. Replace the BCU or main board of

peripherals.

SC 623

Duplex unit

communication

error

While the BCU communicates
with an optional unit, an SC
code is displayed if one of
following conditions occurs.
1. The BCU receives a signal

which is generated by the
peripherals only just after
the main switch is turned
on.

2. When the BCU does not

receive an OK signal from a
peripheral 100ms after
sending a command to it.
The BCU resends the
command. The BCU does
not receive an OK signal
after sending the command
3 times.

•

Cable problems

•

BCU problems

•

PSU problems in the
machine

•

Duplex control board
problem

1. Turn the main switch off and on.
2. Check if the cable of the duplex

inverter unit is properly connected.

3. Replace the PSU if no power is

supplied to the peripherals.

4. Replace the duplex control board in

the inverter unit.

SC 640

BCU -
Controller

communication

error (check
sum error)

The check sum of the interface
between the BCU and
controller is not the same.

•

Defective controller

•

Defective PCU

1. Turn the main switch off and on.
2. Replace the controller.
3. Replace the BCU.

CTL

SC 641

BCU –
Controller

communication

error (no
response)

The controller does not receive
any response from the BCU
three consecutive times when
sending a signal every 100ms.

•

Loose connection

•

Defective controller

•

Defective BCU

1. Turn the main switch off and on.
2. Check the connection between the

BCU and controller.

3. Replace the controller.
4. Replace the BCU.

CTL

SC 660

BCU NVRAM
read/write
diagnostics
error

A read/write diagnostics error
is detected when the main SW
is turned ON.

Note:

This only occurs with the

8kB NVRAM.

•

Defective 8kB
NVRAM (BCU)

1. Turn the main switch OFF/ON.
2. Replace the NVRAM.

⇒

Rev. 09/2003

«
...
136
137
138
139
140
...
»

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды