manualshive.com logo in svg

Gestetner G060, Руководство по обслуживанию

Поделиться
Скачать
Gestetner G060 Скачать руководство пользователя страница 515

SC TABLE

SM

4-33

G570

SC No.

Item

Definition

Possible Cause

Related

SCs

Troubleshooting Procedure

Type

SC 691

(CF)

Scanner startup
error

•

  After the machine is

powered on or recovering
from the power save
mode, the scanner ready
signal is not verified.

•

 Board connector

between controller
and bridge board
loose

•

 Board connector

between bridge board
and IPU loose

•

 IPU board defective

•

 Controller board

defective

•

 Bridge board

defective

1. Turn the main switch off and on.
2. Check the cable connection between

controller and bridge board.

3. Check the cable connection between

bridge board and IPU.

4. Replace the IPU board.
5. Replace the controller board.
6. Replace the bridge board.

B

SC 700

(CF)

ARDF original
pick-up
malfunction

•

  After the pick-up motor is

turned on, the original
stopper HP sensor is not
activated.

•

  Original stopper HP

sensor defective

•

 Pick-up motor

defective (not
rotating)

•

  Timing belt out of

position

•

  ARDF main board

defective

SC 701

1. Turn the main switch off and on.
2. Replace the HP sensor.
3. Turn the main switch off and on.
4. Replace the pick-up motor.
5. Replace the control board.

B

SC 701

(CF)

ARDF original
pick-up/paper lift
mechanism
malfunction

•

  The original pick-up HP

sensor is not activated
after the pick-up motor is
turned on.

•

 Original pick-up HP

sensor defective

•

 Pick-up motor

defective

•

  ARDF main board

defective

SC 700

1. Turn the main switch off and on.
2. Replace the pick-up motor.
3. Replace the control board.
4. Replace the HP sensor.

B

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды