Gestetner G060 Скачать руководство пользователя страница 509 | Manualshive

Страница: 509 / 1106

Gestetner G060 Скачать руководство пользователя страница 509

SC TABLE

SM

4-27

G570

SC No.

Item

Definition

Possible Cause

Related

SCs

Troubleshooting Procedure

Type

SC 544

Heating roller
fusing lamp low
temperature
error

During stand-by mode or a
print job, the detected
heating roller temperature
stays at 50 °C or less for five
seconds.

•

Loose connection

between the fusing
unit and the main
frame

•

Defective heating

roller thermistor

•

Defective PSU

•

Defective BCU

1. Check the connection between the

fusing unit and main frame.

2. Replace the fusing unit.
3. Replace the PSU.
4. Replace the BCU.

A

SC 545

Heating roller
fusing lamp
consecutive full
power

When the fusing unit is not
running in the Ready
condition, the heating roller
fusing lamp keeps on with
full power for 30 consecutive
seconds.

•

Heating roller

thermistor out of
position

1. Replace the fusing unit.

A

SC 546

Heating roller
fusing lamp
temperature
fluctuation

The heating roller
temperature changes by

±

20°C or more in one

second. This occurs three
times in one minute or two
consecutive times.

•

Loose connection of

the thermistor

•

Loose connection

between the fusing
unit and main frame

1. Check if the fusing unit is properly set

and connected to the main frame.

2. Check if the heating roller thermistor

connector is firmly connected.

3. Replace the fusing unit.

A

SC 551

Pressure roller
thermistor error

The measured pressure
roller temperature does not
reach 7°C for 30 seconds.

•

Loose connection of

pressure roller
thermistor

•

Defective pressure

roller thermistor

•

Defective BCU

1. Check that the pressure roller

thermistor is firmly connected.

2. Replace the fusing unit.
3. Replace the BCU.

A

SC 552

Pressure roller
warm-up error

After the main switch is
turned on or the door is
closed, the pressure roller
temperature does not reach
the ready temperature within
150 seconds during fusing
unit warm-up.

•

Pressure roller fusing

lamp broken

•

Defective pressure

roller thermistor

•

Defective BCU

1. Check if the pressure roller thermistor

is firmly connected.

2. Replace the fusing unit.
3. Replace the BCU.

A

«
...
507
508
509
510
511
...
»

Содержание G060



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды