Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 3

Страница: 3 / 168

Proline Prosonic Flow 93 PROFIBUS DP/PA

Table of contents

Hauser

Table of contents

Safety instructions . . . . . . . . . . . . . . . . 5

1.1

Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2

Installation, commissioning and operation . . . . . . . . 5

1.3

Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4

Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.5

Notes on safety conventions and icons . . . . . . . . . . . 6

Identification . . . . . . . . . . . . . . . . . . . . 7

2.1

Device designation   . . . . . . . . . . . . . . . . . . . . . . . . .  7
2.1.1  Nameplate of the transmitter  . . . . . . . . . . . .  7
2.1.2  Nameplate of the sensor   . . . . . . . . . . . . . . .  8
2.1.3  Nameplate for the connections   . . . . . . . . . .  9

2.2

Certificates and approvals . . . . . . . . . . . . . . . . . . . 10

2.3

Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 10

Installation . . . . . . . . . . . . . . . . . . . . . 11

3.1

Incoming acceptance, transport and storage  . . . . . .  11
3.1.1  Incoming acceptance  . . . . . . . . . . . . . . . . .  11
3.1.2  Transport   . . . . . . . . . . . . . . . . . . . . . . . . .  11
3.1.3  Storage  . . . . . . . . . . . . . . . . . . . . . . . . . . .  11

3.2

Installation conditions  . . . . . . . . . . . . . . . . . . . . . .  11
3.2.1  Dimensions    . . . . . . . . . . . . . . . . . . . . . . .  11
3.2.2  Mounting location   . . . . . . . . . . . . . . . . . .  11
3.2.3  Orientation  . . . . . . . . . . . . . . . . . . . . . . . .  12
3.2.4  Inlet and outlet run  . . . . . . . . . . . . . . . . . .  12
3.2.5  Sensor selection and arrangement   . . . . . . .  13

3.3

Two-channel operation . . . . . . . . . . . . . . . . . . . . .  14
3.3.1  Two-channel measurement  . . . . . . . . . . . .  14
3.3.2  Two-path measurement . . . . . . . . . . . . . . .  15

3.4

Preparatory steps prior to installation . . . . . . . . . . . 16

3.5

Determining the necessary installation distances   . .  16
3.5.1  Installation distances for Prosonic Flow P  . .  16
3.5.2  Installation distances for Prosonic W   . . . . .  16

3.6

Determining values for installation distances . . . . . 17
3.6.1 Determining installation distances

via local operation . . . . . . . . . . . . . . . . . . . 17

3.6.2 Determining installation distances

via FieldCare . . . . . . . . . . . . . . . . . . . . . . . 22

3.6.3 Determining installation distances

via Applicator . . . . . . . . . . . . . . . . . . . . . . 28

3.7

Mechanical preparation . . . . . . . . . . . . . . . . . . . . . 30
3.7.1 Mounting the sensor holder

with U-shaped screws . . . . . . . . . . . . . . . . 30

3.7.2 Mounting the sensor holder

with strapping bands . . . . . . . . . . . . . . . . . 31

3.7.3 Premounting the strapping bands

(medium nominal diameters) . . . . . . . . . . . 32

3.7.4 Premounting the strapping bands

(large nominal diameters) . . . . . . . . . . . . . 33

3.7.5 Mounting the welded bolts . . . . . . . . . . . . 34

3.8

Installing Prosonic Flow P
DN 15 to 65 (½ to 2½") . . . . . . . . . . . . . . . . . . . . 35
3.8.1 Mounting the sensor . . . . . . . . . . . . . . . . . 35

3.9

Installing Prosonic Flow P
DN 50 to 4000 (2 to 160"), Clamp-on . . . . . . . . . . 37
3.9.1 Installation for measurement

via one traverse . . . . . . . . . . . . . . . . . . . . . 37

3.9.2 Installation for measurement

via two traverses . . . . . . . . . . . . . . . . . . . . 39

3.10 Installing Prosonic Flow W (Clamp-on) . . . . . . . . . 41

3.10.1 Installation for measurement

via one traverse . . . . . . . . . . . . . . . . . . . . . 41

3.10.2 Installation for measurement

via two traverses . . . . . . . . . . . . . . . . . . . . 43

3.11 Installing Prosonic Flow W (Insertion version) . . . . 45

3.11.1 Installation for measurement

as single-path insertion version . . . . . . . . . . 46

3.11.2 Installation for measurement

as dual-path insertion version . . . . . . . . . . . 49

3.12 Installing sensor DDU18 . . . . . . . . . . . . . . . . . . . . 53
3.13 Installing sensor DDU19 . . . . . . . . . . . . . . . . . . . . 54

3.13.1 Version 1 . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3.13.2 Version 2 . . . . . . . . . . . . . . . . . . . . . . . . . . 54

3.14 Installing the wall-mount transmitter housing . . . . . 55

3.14.1  Direct wall mounting  . . . . . . . . . . . . . . . . . 55
3.14.2  Panel mounting  . . . . . . . . . . . . . . . . . . . . . 56
3.14.3  Pipe mounting  . . . . . . . . . . . . . . . . . . . . . .  56

3.15 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 57

Wiring . . . . . . . . . . . . . . . . . . . . . . . . . 58

4.1

PROFIBUS cable specifications  . . . . . . . . . . . . . . . . 58
4.1.1  PROFIBUS DP cable specifications  . . . . . . . 58
4.1.2  PROFIBUS PA cable specifications  . . . . . . .  60
4.1.3  Shielding and grounding   . . . . . . . . . . . . . . 62

4.2

Sensor/transmitter connecting cable . . . . . . . . . . . 62
4.2.1 Connecting Prosonic Flow W and P

DN 50 to 4000 (2 to 160") . . . . . . . . . . . . 63

4.2.2 Grounding Prosonic Flow P

DN 15 to 65 (½ to 2½") . . . . . . . . . . . . . . 65

4.2.3 Cable specification for connecting cable . . . 65

4.3

Connecting the measuring unit   . . . . . . . . . . . . . . . 66
4.3.1  Terminal assignment  . . . . . . . . . . . . . . . . . 66
4.3.2  Connecting the transmitter   . . . . . . . . . . . . 67
4.3.3  PROFIBUS DP connection diagram   . . . . . . 68
4.3.4  PROFIBUS PA connection diagram . . . . . . . 70

4.4

Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 73

4.5

Post-connection check . . . . . . . . . . . . . . . . . . . . . . 74

Содержание Proline Prosonic Flow 93









































































































































































Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды

Endress+Hauser Proline Prosonic Flow 93, Руководство по эксплуатации

Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды