Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 168

background image

Installation

Proline Prosonic Flow 93 PROFIBUS DP/PA

14

Hauser

3.3

Two-channel operation

The transmitter is able to operate two independent measuring channels (measuring channel 1 and
measuring channel 2). A pair of sensors is connected per measuring channel. Both measuring
channels operate independently of one another and are supported by the transmitter to an equal
extent.

Two-channel operation can be used for the following measurements:
• Two-channel measurement = flow measurement at two separate measuring points
• Two-path measurement = redundant flow measurement at one measuring point

3.3.1

Two-channel measurement

The flow is measured at two separate measuring points in the case of two-channel measurement.

The measured values of the two measuring channels can be processed and displayed differently.
The following measured values can be output for two-channel measurement:
• Individual measured values per measuring channel (output independently of one another)
• The difference between the two measured values
• The sum of the two measured values

The two measuring channels can be configured individually. This makes it possible to independently
configure and select the display, outputs, sensor type and type of installation.

A0001159

Fig. 8:

Two-channel measurement: example of arranging sensor pairs at two separate measuring points

A

Measuring channel 1: mounting the sensor pair for measurement via two traverses

B

Measuring channel 2: mounting the sensor pair for measurement via one traverse

B

A

«
...
12
13
14
15
16
...
»

Содержание Proline Prosonic Flow 93









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Prosonic Flow 93

Бренд: Kane Страницы: 12

Бренд: Kane Страницы: 4

Бренд: C-LOGIC Страницы: 4

Бренд: C-lock Страницы: 32

Бренд: C-LOGIC Страницы: 12

Бренд: Wavetek Страницы: 43

Бренд: Harley Benton Страницы: 28

Бренд: National Instruments Страницы: 12

Бренд: Oldham Страницы: 96

Бренд: RIDGID Страницы: 18

Бренд: CAS Corporation Страницы: 20

Бренд: IDT Страницы: 20

Бренд: Vega Страницы: 44

EUROGRAND EG2080

Бренд: Behringer Страницы: 34

Бренд: Feasa Страницы: 145

Бренд: DynAmp Страницы: 43

Бренд: T&D Страницы: 2

Бренд: Omega Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды