Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 158

Страница: 158 / 168

Technical data

Proline Prosonic Flow 93 PROFIBUS DP/PA

158

Hauser

10.1.8

Operating conditions: environment

Ambient temperature range

Transmitter

–20 to +60 °C (–4 to +140 °F)

Sensor

• Standard: –40 to +80 °C (–40 to +176 °F)
• Optional: 0 to +170 °C (+32 to +338 °F)

DDU18 sensor (accessories: sound velocity measurement)

–40 to +80 °C (–40 to +176 °F)

DDU19 sensor (accessories: wall thickness measurement)

–20 to +60 °C (–4 to +140 °F)

Connecting cable (sensor/transmitter)

• Standard (PVC): –20 to +70 °C (–4 to +158 °F)
• Optional (PTFE): –40 to +170 °C (–40 to +338 °F)

Note!
• It is permitted to insulate the sensors mounted on the pipes.
• Mount the transmitter in a shady location and avoid direct sunlight, particularly in warm climatic

regions.

Storage temperature

The storage temperature corresponds to the ambient temperature range.

Degree of protection

Transmitter

IP 67 (NEMA 4X)

Sensor

IP 68 (NEMA 6P)

DDU18 sensor (accessories: sound velocity measurement)

IP 68 (NEMA 6P)

DDU19 sensor (accessories: wall thickness measurement)

IP 67 (NEMA 4X)

Shock and vibration resistance

According to IEC 68-2-6

Electromagnetic compatibility
(EMC)

Electromagnetic compatibility (EMC requirements) according to IEC/EN 61326 "Emission to
class A requirements" and NAMUR Recommendation NE 21/43.

Содержание Proline Prosonic Flow 93









































































































































































Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды

Endress+Hauser Proline Prosonic Flow 93, Руководство по эксплуатации

Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды