Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 168

background image

Technical data

Proline Prosonic Flow 93 PROFIBUS DP/PA

162

Hauser

Other standards and
guidelines

• EN 60529

Degrees of protection provided by enclosures (IP code).

• EN 61010-1

Safety requirements for electrical equipment for measurement, control and laboratory use.

• IEC/EN 61326

"Emission in accordance with Class A requirements".
Electromagnetic compatibility (EMC requirements).

• ANSI/ISA-S82.01

Safety Standard for Electrical and Electronic Test, Measuring, Controlling and Related
Equipment - General Requirements. Pollution Degree 2, Installation Category II.

• CAN/CSA-C22.2 No. 1010.1-92

Safety Requirements for Electrical Equipment for Measurement and Control and Laboratory Use.
Pollution Degree 2, Installation Category II.

• NAMUR NE 21

Electromagnetic compatibility (EMC) of industrial process and laboratory control equipment.

• NAMUR NE 43

Standardization of the signal level for the breakdown information of digital transmitters with
analog output signal.

• NAMUR NE 53

Software of field devices and signal-processing devices with digital electronics.

10.1.13 Ordering information

The Hauser service organization can provide detailed ordering information and
information on the order codes on request.

10.1.14 Documentation

• Flow measurement (FA005D)
• Technical Information for Promass Flow 93P (TI083D)
• Technical Information for Prosonic Flow 93W (TI084D)
• Description of Device Functions for Prosonic Flow 93 PROFIBUS DP/PA (BA077D)
• Supplementary documentation on Ex-ratings: ATEX, FM, CSA, IEC, NEPSI

«
...
160
161
162
163
164
...
»

Содержание Proline Prosonic Flow 93









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Prosonic Flow 93

Бренд: Kawai Страницы: 70

Бренд: XS Scuba Страницы: 24

CellaCast PA8 Series

Бренд: Keller Страницы: 12

Бренд: KROHNE Страницы: 56

Бренд: SKF Страницы: 12

Бренд: Badger Meter Страницы: 24

Litemaster Pro L-478DR

Бренд: Sekonic Страницы: 16

Бренд: Major tech Страницы: 20

Бренд: Alma Страницы: 69

Бренд: Milkotester Страницы: 44

Бренд: Dewetron Страницы: 48

Бренд: Cable Detection Страницы: 2

Combo Electric Harpsichord

Бренд: Jiggery-Pokery Страницы: 13

Бренд: Myron L Страницы: 2

Бренд: Interscan Corporation Страницы: 23

Бренд: Keysight Страницы: 583

Moisture Encounter Plus

Бренд: TRAMEX Страницы: 13

Бренд: Elenco Electronics Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды