Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 168

background image

Proline Prosonic Flow 93 PROFIBUS DP/PA

Wiring

Hauser

73

4.4

Degree of protection

Transmitter (wall-mount housing)

The transmitter fulfills all the requirements for IP 67.

"

Achtung!
Do not loosen the screws of the sensor housing, as otherwise the degree of protection guaranteed
by Hauser no longer applies.

Compliance with the following points is mandatory following installation in the field or servicing,
in order to ensure that IP 67 protection is maintained:
• The housing seals must be clean and undamaged when inserted into their grooves. The seals must

be dried, cleaned or replaced if necessary.

• All the threaded fasteners and screw covers must be firmly tightened.
• The cables used for connection must be of the specified outside diameter

• Securely tighten the cable entries

• Remove all unused cable entries and insert plugs instead.
• Do not remove the grommet from the cable entry.

A0001138

Fig. 72:

Installation instructions for cable entries on the transmitter housing

Prosonic Flow P and W sensor (Clamp-on / Insertion version), DDU 18

The flowrate sensors Prosonic Flow P and W, as well as the sound velocity sensors DDU 18, meet
all the requirements for IP 67 or IP 68 degree of protection (please observe the information on the
nameplate of the sensor).

Compliance with the following points is mandatory following installation in the field or servicing,
in order to ensure that IP 67/68 protection is maintained:
• Only use connecting cables supplied by Hauser with the corresponding cable

connectors.

• When connecting, do not jam the cable connectors. Tighten them to the stop.
• The cable connector seals must be clean, dry and undamaged when inserted in the seal

groove

73 (1).

A0001139

Fig. 73:

Cable connector

1

Cable connector seal

1

«
...
71
72
73
74
75
...
»

Содержание Proline Prosonic Flow 93









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Prosonic Flow 93

Бренд: WAGER Страницы: 22

Бренд: janitza Страницы: 12

Бренд: janitza Страницы: 84

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 14

Бренд: janitza Страницы: 98

Бренд: QMI Страницы: 54

Бренд: M-system Страницы: 13

Prestige Series

Бренд: Ibanez Страницы: 54

Бренд: Magene Страницы: 80

Бренд: Endress+Hauser Страницы: 88

Бренд: Keysight Страницы: 92

Бренд: Trebs Страницы: 44

Greenlee CLM-1000

Бренд: Textron Страницы: 36

Бренд: Oldham Страницы: 96

Бренд: Armstrong Monitoring Corporation Страницы: 12

Бренд: Veeco Страницы: 349

Бренд: GrainPro Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды