Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 168

background image

Wiring

Proline Prosonic Flow 93 PROFIBUS DP/PA

62

Hauser

4.1.3

Shielding and grounding

When planning the shielding and grounding for a fieldbus system, there are three important points
to consider:

• Electromagnetic compatibility (EMC)
• Explosion protection
• Safety of the personnel

To ensure the optimum electromagnetic compatibility of systems, it is important that the system
components and above all the cables, which connect the components, are shielded and that no
portion of the system is unshielded. Ideally, the cable shields are connected to the normally metal
housings of the connected field devices. Since these are generally connected to the protective earth,
the shield of the bus cable is grounded many times. Keep the stripped and twisted lengths of cable
shield to the terminals as short as possible.
This approach, which provides the best electromagnetic compatibility and personal safety, can be
used without restriction in systems with good potential matching.
In the case of systems without potential matching, a power supply frequency (50 Hz) equalizing
current can flow between two grounding points which, in unfavorable cases, e.g. when it exceeds
the permissible shield current, may destroy the cable.
To suppress the low frequency equalizing currents on systems without potential equalization, it is
therefore recommended to connect the cable shield directly to the building ground (or protective
earth) at one end only and to use capacitive coupling to connect all other grounding points.

"

Caution!
The legal EMC requirements are fulfilled

only

when the cable shield is grounded on both sides!

4.2

Sensor/transmitter connecting cable

#

Warning!
• Risk of electric shock. Switch off the power supply before opening the device. Do not install or

wire the device while it is connected to the power supply. Failure to comply with this precaution
can result in irreparable damage to the electronics.

• Risk of electric shock. Connect the protective ground to the ground terminal on the housing

before the power supply is applied.

!

Note!
To ensure correct measuring results, route the cable well clear of electrical machines and switching
elements.

«
...
60
61
62
63
64
...
»

Содержание Proline Prosonic Flow 93









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Prosonic Flow 93

Бренд: ABB Страницы: 8

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

DC1500 CHLORINE

Бренд: LaMotte Страницы: 60

Бренд: M-system Страницы: 16

Бренд: M-system Страницы: 25

Бренд: YOKOGAWA Страницы: 16

Бренд: Valcom Страницы: 1

Бренд: PCB Piezotronics Страницы: 15

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Magnescale Страницы: 2

Proline Promag 10D

Бренд: Endress+Hauser Страницы: 28

Бренд: Major tech Страницы: 16

AUER Atemluft 300 bar

Бренд: MSA Страницы: 52

Бренд: Heyuan Intelligence Страницы: 14

LaserRange-Master i5

Бренд: LaserLine Страницы: 68

Бренд: E+E Elektronik Страницы: 48

Prolevel FMC 662

Бренд: Endress+Hauser Страницы: 52

Бренд: Alcor System Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды