Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 149

Страница: 149 / 168

Proline Prosonic Flow 93 PROFIBUS DP/PA

Troubleshooting

Hauser

149

9.6.4

Installing and removing the W sensors

The active part of the flowrate measuring sensor W "Insertion" can be replaced without interrupting
the process.

Pull the sensor connector (1) out of the sensor cover (3).

Remove the small retainer ring (2). This is located on the top of the sensor neck and keeps the
sensor cover in place.

Remove the sensor cover (3) and spring (4).

Remove the large retainer ring (5). This keeps the sensor neck (6) in place.

The sensor neck can now be pulled out. Note that you must reckon with a certain amount of
resistance.

Pull the sensor element (7) out of the sensor holder (8) and replace it with a new one.

Installation is the reverse of the removal procedure.

Caution!
Use only original Hauser parts.

A0001147

Fig. 100: Flow measuring sensor W "Insertion": installation/removal

Sensor connector

Small retainer ring

Sensor cover

Spring

Large retainer ring

Sensor neck

Sensor element

Sensor holder

Содержание Proline Prosonic Flow 93









































































































































































Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды

Endress+Hauser Proline Prosonic Flow 93, Руководство по эксплуатации

Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды