Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 33

Страница: 33 / 168

Proline Prosonic Flow 93 PROFIBUS DP/PA

Installation

Hauser

3.7.4

Premounting the strapping bands (large nominal diameters)

When mounting on a pipe with a nominal diameter of DN

200 (8")

For sensors:
• Prosonic Flow 93P (DN 50 to 4000 / 2 to 160")
• Prosonic Flow 93W

Procedure

Measure the pipe circumference.

Shorten the strapping bands to one length (pipe circumf 10 cm (3.94")) and trim the
cut edges.

Warning!

Risk of injury. To avoid sharp edges, trim the cut edges after shortening the strapping bands.

First strapping band

Fit the centering plate along with the mounting bolt over the strapping band.

Wrap the strapping band around the pipe without twisting it.

Guide the end of the strapping band through the strapping band lock (strapping screw is
pushed up).

Tighten the strapping band as tight as possible by hand.

Set the strapping band to the desired position.

Push down the strapping screw and tighten the strapping band so that it cannot slip.

Second strapping band

Proceed as for the first strapping band (steps 3 to 8). Only slightly tighten the second strapping
band for final mounting. It must be possible to move the strapping band for final alignment.

A0001110

Fig. 23:

Premounting strapping bands for pipe diameters DN > 200 (8")

Centering plate with mounting bolt

Strapping band

Strapping screw

Содержание Proline Prosonic Flow 93









































































































































































Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды

Endress+Hauser Proline Prosonic Flow 93, Руководство по эксплуатации

Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды