Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 168

background image

Commissioning

Proline Prosonic Flow 93 PROFIBUS DP/PA

96

Hauser

6.4

Commissioning the PROFIBUS interface

!

Note!
• All functions required for commissioning are described in detail in the "Description of Device

Functions" manual which is a separate part of these Operating Instructions.

• A code (factory setting: 93) must be entered to change device functions, numerical values or

factory settings

6.4.1

PROFIBUS DP commissioning

The following steps must be carried out in the sequence specified:

1.

Check the hardware write protection:

The WRITE PROTECT (6102) parameter indicates whether it is possible to write to the device
functions via PROFIBUS (acyclic data transmission, e.g. via the operating program "FieldCare").

!

Note!

This check is not needed if operating via the local display.

BASIC FUNCTION (G)

→

PROFIBUS DP (GBA)

→

CONFIGURATION (610)

→

WRITE PROTECT (6102)

→

Display of one of the following options:

– OFF (factory setting) = write access via PROFIBUS possible
– ON = write access via PROFIBUS not possible

Deactivate the write protection if necessary

2.

Enter the tag name (optional):

BASIC FUNCTION (G)

→

PROFIBUS DP (GBA)

→

CONFIGURATION(610)

→

TAG NAME (6100)

3.

Configuring the fieldbus address:

Software addressing using the local display or an operating program:
BASIC FUNCTION (G)

→

PROFIBUS DP (GBA)

→

CONFIGURATION (610)

→

FIELDBUS ADDRESS (6101)

Hardware addressing via miniature switches

4.

Select the system unit:

a. Determine the units by means of the system units group:

MEASURED VARIABLES (A)

→

SYSTEM UNITS (ACA)

→

CONFIGURATION (040)

→

UNIT MASS FLOW (0400) / UNIT MASS (0401) / UNIT
VOLUME FLOW (0402) / …

b. In the function UNIT TO BUS (6141), select the option SET UNITS, so that the measured

variables transmitted cyclically to the PROFIBUS master (Class 1) are transmitted with the
system units set in the measuring device:
BASIC FUNCTION (G)

→

PROFIBUS DP (GBA)

→

OPERATION (614)

→

UNIT TO BUS (6141)

!

Note!

• The configuration of the system units for the totalizer is described separately

→

see step 7

• If the system unit of a measured variable is changed by means of the local operation or an

operating program, this initially does not have any effect on the unit that is used to transmit
the measured variable to the PROFIBUS master (Class 1). Changed system units of the
measured variables are not transmitted to the PROFIBUS master (Class 1) until the SET
UNITS option is activated in the function BASIC FUNCTION (G)

→

PROFIBUS DP (GBA)

→

OPERATION (614)

→

UNIT TO BUS (6141).

«
...
94
95
96
97
98
...
»

Содержание Proline Prosonic Flow 93









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Prosonic Flow 93

Бренд: Kanomax Страницы: 2

Бренд: Keithley Страницы: 156

Бренд: 3nh Страницы: 10

Бренд: Bante Instruments Страницы: 6

Бренд: Dallas Brass Страницы: 19

Бренд: DGH Страницы: 87

Бренд: Teledyne Lecroy Страницы: 4

Бренд: horiba Страницы: 175

VX200-N-VI Series

Бренд: XS Scuba Страницы: 34

Бренд: Hanna Instruments Страницы: 25

Бренд: Deprag Страницы: 28

SS9007.3 Mini CT Meter

Бренд: Saturn South Страницы: 18

Rainbow RTI-Nano Series

Бренд: Laserworld Страницы: 25

Бренд: Maxtec Страницы: 13

PROline promag 23

Бренд: Endress+Hauser Страницы: 108

Military ALTITRACK

Бренд: Larsen & Brusgaard Страницы: 46

Бренд: Oakton Страницы: 10

Бренд: Stabila Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды