Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 63

Страница: 63 / 168

Proline Prosonic Flow 93 PROFIBUS DP/PA

Wiring

Hauser

4.2.1

Connecting Prosonic Flow W and P DN 50 to 4000 (2 to 160")

Procedure

→

Remove the cover (a) of the connection compartment.

Remove the dummy cover from the cable entry (b).

Route the two connecting cables (c) of channel 1 through the cable gland (d).

Route the two connecting cables of channel 1 through the cable entry (b) and into the
connection compartment of the transmitter.

Place the cable retaining sleeves (e) of the two connecting cables at the ground contact
terminals (f) (Detail B).

Twist down the ground contact terminals (f) so that the two cable retaining sleeves (e) are
firmly seated.

Screw the ground contact terminals (f) tight.

Note!

The Prosonic Flow P DN 15 to 65 (½ to 2½") is grounded via the cable gland

→

65.

Connect the connecting cable:
– Channel 1 upstream = 1
– Channel 1 downstream = 2
– Channel 2 upstream = 3
– Channel 3 downstream = 4

Spread the rubber seal (g) along the side slit with a suitable tool (e.g. a large screwdriver) and
fix both connecting cables into place.

10. Push the rubber seal (g) up into the cable entry (b).

11. Tighten the cable gland (d).

12. Fit the cover (a) on the connection compartment and screw it on.

Note!

The connection compartment does not have to be assembled if the transmitter is wired (power
supply and signal cable) directly afterwards.

Содержание Proline Prosonic Flow 93









































































































































































Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды

Endress+Hauser Proline Prosonic Flow 93, Руководство по эксплуатации

Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды