Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 168

background image

Accessories

Proline Prosonic Flow 93 PROFIBUS DP/PA

132

Hauser

8

Accessories

Various accessories, which can be ordered separately from Hauser, are available for the
transmitter and the sensor. The Hauser service organization can provide detailed
information on the order codes on request.

Device-specific accessories

Accessory

Description

Order code

Wall-mount housing,
transmitter
Prosonic Flow 93

Transmitter for replacement or for stock. Use the order code
to define the following specifications:
• Approvals
• Degree of protection/version
• Cable entry
• Display / power supply / operation
• Software
• Outputs / inputs

Single-channel version:
93XXX - XX1XX********

Two-channel version:
93XXX - XX2XX********

Conversion kit,
inputs/outputs

Conversion kit with appropriate plug-in point modules for
converting the current input/output configuration to a new
version.

DK9UI - **

Sensor P
(DN 15 to 65 / ½ to 2½")
Clamp-on version

DN 15 to 65 (½ to 2½")
• –40 to +100 °C (–40 to +212 °F)
• –40 to +150 °C (–40 to +302 °F)

DK9PS - 1*
DK9PS - 2*

Sensor P
(DN 50 to 4000 / 2 to 160")
Clamp-on version

DN 50 to 300 (2 to 12")
• –40 to +80 °C (–40 to +176 °F)
• –40 to +170 °C (–40 to +338 °F)

DK9PS - B*
DK9PS - F*

DN 100 to 4000 (4 to 160")
• –40 to +80 °C (–40 to +176 °F)
• –40 to +170 °C (–40 to +338 °F)

DK9PS - A*
DK9PS - E*

Sensor W
(DN 50 to 4000 / 2 to 160")
Clamp-on version

DN 50 to 300 (2 to 12"), –20 to +80 °C (–4 to +176 °F),
2.0 MHz
• IP 67 / NEMA 4X
• IP 68 / NEMA 6P

DK9WS - B*
DK9WS - N*

DN 100 to 4000 (4 to 160"), –20 to +80 °C (–4 to +176 °F),
1.0 MHz
• IP 67 / NEMA 4X
• IP 68 / NEMA 6P

DK9WS - A*
DK9WS - M*

DN 100 to 4000 (4 to 160"), 0 to +130 °C (+32 to +266 °F),
1.0 MHz
• IP 67 / NEMA 4X

DK9WS - P*

DN 50 to 300 (2 to 12"), 0 to +130 °C (+32 to +266 °F),
2.0 MHz
• IP 67 / NEMA 4X

DK9WS - S*

DN 100 to 4000 (4 to 160"), –20 to +80 °C ( –4 to +176 °F),
0.5 MHz
• IP 67 / NEMA 4X
• IP 68 / NEMA 6P

DK9WS - R*
DK9WS - T*

Sensor W
(DN 200 to 4000 / 8 to 160")
Insertion version

DN 200 to 4000 (8 to 160"), –40 to +80 °C (–40 to +176 °F) DK9WS - K*

Sensor DDU18

Sensor for sound velocity measurement
• –40 to +80 °C (–40 to +176 °F)
• 0 to +170 °C (+32 to +338 °F)

50091703
50091704

Sensor DDU19

Sensor for wall thickness measurement.

50091713

«
...
130
131
132
133
134
...
»

Содержание Proline Prosonic Flow 93









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Prosonic Flow 93

Бренд: ABB Страницы: 8

Бренд: 3nh Страницы: 10

Бренд: Galileo Страницы: 19

Бренд: Galileo Страницы: 71

Бренд: Midcontinent Страницы: 6

Бренд: PCB Piezotronics Страницы: 15

BUCKMASTERS 1500

Бренд: Sig Sauer Страницы: 2

Бренд: Fly Henry Страницы: 5

Бренд: Maico Страницы: 2

Бренд: Dadam micro Страницы: 24

Бренд: promesstec Страницы: 72

Бренд: Universal Laser Systems Страницы: 100

Photo Set Strato S-20

Бренд: Fisso Страницы: 2

Бренд: Fungilab Страницы: 47

Superstatic 749

Бренд: Sontex Страницы: 24

Micropilot S FMR 53 Series

Бренд: E+H Страницы: 12

Бренд: SmarTire Страницы: 14

Бренд: LaserLine Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды