Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 46

Страница: 46 / 168

Installation

Proline Prosonic Flow 93 PROFIBUS DP/PA

Hauser

3.11.1

Installation for measurement as single-path insertion version

Determine the installation area (e) on the pipe section:
– Mounting location

→

– Inlet/outlet run

→

– Space required by the measuring point: approx. 1× pipe diameter.

Mark the middle line on the pipe at the mounting location and mark the position of the first
drillhole (drillhole diameter: 65 mm / 2.56").

Note!

Make the middle line longer than the drillhole!

A0001124

Fig. 47:

Installing the measuring sensors, steps 1 and 2

Cut the first hole, e.g. with a plasma cutter. Measure the wall thickness of the pipe if it is not
known.

Determine the sensor distance.

Note!

Determine the sensor distance as follows:
– Via the Quick Setup "Sensor Installation" for measuring devices with local operation.

Run the Quick Setup as described on

→

90. The sensor distance is displayed in the

SENSORABSTAND function. The transmitter must be installed and connected to the power
supply before you can run the "Sensor Installation" Quick Setup.

– As explained on

→

90 for transmitters without local operation.

A0001125

Fig. 48:

Installing the measuring sensors, steps 3 and 4

Draw the sensor distance (a) starting from the middle line of the first drillhole.

Содержание Proline Prosonic Flow 93









































































































































































Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды

Endress+Hauser Proline Prosonic Flow 93, Руководство по эксплуатации

Результаты поиска

Содержание Proline Prosonic Flow 93

Отзывы:

Похожие инструкции для Proline Prosonic Flow 93

Бренды по названию

Популярные бренды