Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 168

background image

Installation

Proline Prosonic Flow 93 PROFIBUS DP/PA

34

Hauser

3.7.5

Mounting the welded bolts

When mounting on a pipe with a nominal diameter of DN 50 to 4000 (2 to 160")

For sensors:
• Prosonic Flow 93P (DN 50 to 4000 / 2 to 160")
• Prosonic Flow 93W

Procedure

The welded bolts must be fixed at the same installation distances as the mounting bolts with
strapping bands. The following sections explain how to the align the mounting bolts depending on
the type of mounting and the measurement method:
• Prosonic Flow P (DN 50 to 4000 / 2 to 160"), Clamp-on

– Installation for measurement via one traverse

– Installation for measurement via two traverses

• Prosonic Flow W, Clamp-on

– Installation for measurement via one traverse

– Installation for measurement via two traverses

The sensor holder is secured with a retaining nut with a metric ISO M6 thread as standard. If you
want to use another thread to secure the sensor holder, you must use a sensor holder with a
removable retaining nut (order number: 93WAx - xBxxxxxxxxxx).

A0001111

Fig. 24:

Use of welded bolts

1

Welding seam

2

Retaining nut

3

Hole diameter max. 8.7 mm (0.34")

M6

50

1

2

3

1

«
...
32
33
34
35
36
...
»

Содержание Proline Prosonic Flow 93









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Prosonic Flow 93

Бренд: VELOCICALC Страницы: 6

Бренд: Panametrics Страницы: 68

Бренд: J.P. Instruments Страницы: 9

Бренд: J.ASSY Страницы: 13

Бренд: Gearx Страницы: 19

Бренд: Velleman Страницы: 107

Dakota Ultrasonics ZX-2

Бренд: ABQ Industrial Страницы: 27

Бренд: King Instrument Страницы: 5

Бренд: OmegaWatt Страницы: 9

Engine Analyzer Series

Бренд: ACCEL DFI Страницы: 39

Бренд: Hach Страницы: 2

Бренд: East Tester Страницы: 36

Бренд: LaserLine Страницы: 15

Military ALTITRACK

Бренд: Larsen & Brusgaard Страницы: 46

Бренд: Powerline Страницы: 12

Бренд: Sperry instruments Страницы: 8

Бренд: HCI Страницы: 3

Бренд: UMS Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды