Endress+Hauser Proline Prosonic Flow 93 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 168

background image

Installation

Proline Prosonic Flow 93 PROFIBUS DP/PA

28

Hauser

3.6.3

Determining installation distances via Applicator

Applicator is a software application for selecting and planning flowmeters. The installation distances
required for installation can be determined without having to commission the transmitter
beforehand.

Applicator is available:
• On a CD-ROM for installation on a local PC

• Via the Internet for direct online entry

→

www.endress.com

→

select country.

On the Internet site, select

→

Instruments

→

Flow

→

Tooling

→

Applicator. In the "Applicator

Sizing Flow" field, select the "Start Applicator Sizing Flow online" link.

Determining installation distances for clamp-on, measuring via one traverse

Determine the installation distances required via Applicator:
• Select the fluid.
• Select the device (e.g. 93P Clamp-on).
• Enter or select measuring point-specific values.
• Select the number of traverses: 1
• Read off the necessary installation distances:

– Wire length: __________
– Sensor distance: __________

Subsequent procedure

The sensors can be installed once the installation distances have been determined:
• Prosonic Flow P (DN 50 to 4000 / 2 to 160")

• Prosonic Flow W

Determining installation distances for clamp-on, measuring via two traverses

Determine the installation distances required via Applicator:
• Select the fluid.
• Select the device (e.g. 93P Clamp-on).
• Enter or select measuring point-specific values.
• Select the number of traverses: 2
• Read off the necessary installation distances:

– Sensor position: __________
– Sensor distance: __________

Subsequent procedure

The sensors can be installed once the installation distances have been determined:
• Prosonic Flow P (DN 15 to 65 / ½ to 2½")

• Prosonic Flow P (DN 50 to 4000 / 2 to 160")

• Prosonic Flow W

Determining installation distances for insertion version, single-path measurement

Determine the installation distances required via Applicator:
• Select the fluid.
• Select the device (e.g. 93W Insert 1Ch).
• Enter or select measuring point-specific values.
• Read off the necessary installation distance:

– Sensor distance: __________

Subsequent procedure

The sensors can be installed once the installation distances have been determined:
• Prosonic Flow W

«
...
26
27
28
29
30
...
»

Содержание Proline Prosonic Flow 93









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Prosonic Flow 93

Бренд: Bartington Страницы: 15

Бренд: Bartec Страницы: 216

Бренд: YOKOGAWA Страницы: 2

Бренд: Keithley Страницы: 55

Бренд: ICP DAS USA Страницы: 71

HYDROTECHNIK MultiHandy 2025

Бренд: ICS Страницы: 8

Бренд: ICT International Страницы: 24

Бренд: Velleman Страницы: 16

Бренд: Velleman Страницы: 4

Бренд: Velleman Страницы: 8

Бренд: velocomp Страницы: 4

Бренд: Ecolab Страницы: 95

Бренд: OHAUS Страницы: 71

Бренд: Leica Страницы: 2

DIGIMET E30 Preset

Бренд: MATO Страницы: 20

Бренд: PCB Piezotronics Страницы: 11

Бренд: Alpes Lasers Страницы: 41

Бренд: Thermo Scientific Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды