Daikin VRV RXYMQ-A Series Скачать руководство пользователя страница 176

Страница: 176 / 305

Troubleshooting by Error Code

SiME332106E

170

Part 6 Service Diagnosis

5.7.3 Indoor Fan Motor Abnormality (FXFSQ-AR)

Applicable
Models

FXFSQ-AR

Error Code

A6-10

Method of Error
Detection



Detection from the current flow on the fan PCB (A1P)



Detection from the rotation speed of the fan motor in operation



Detection from the position signal of the fan motor



Detection from the current flow on the fan PCB when the fan motor starting operation

Error Decision
Conditions



An overcurrent flows



The rotation speed is less than a certain level for 6 seconds.



A position error in the fan rotor continues for 5 seconds or more.

Supposed
Causes



Clogged foreign matter



Disconnection of fan motor connectors



Fan motor lock



Defective fan motor



Defective indoor unit PCB

Troubleshooting

Connect the connector correctly.

Turn OFF the power supply and
wait for 10 minutes.

Turn ON the power supply and
check the HAP lamp on the indoor
unit control PCB (A1P).

YES

Replace the fan motor (M1F).

YES

Replace the fan motor (M1F).

Resistance

between UVW of fan

motor is unbalanced, or

short-circuited.

YES

The fan

motor connector (

∗

1) is

connected to the indoor unit

control PCB

(A1P).

Remove the foreign matter.

YES

There is a foreign

matter around the fan.

It is

possible to rotate

the fan manually when the

fan motor connector is

disconnected from the indoor

unit control PCB

(A1P).

Caution

Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.

Go to the next page.

Содержание VRV RXYMQ-A Series


















































































































































































































































































































Результаты поиска

Содержание VRV RXYMQ-A Series

Отзывы:

Похожие инструкции для VRV RXYMQ-A Series

Бренды по названию

Популярные бренды

Daikin VRV RXYMQ-A Series, Руководство по обслуживанию

Результаты поиска

Содержание VRV RXYMQ-A Series

Отзывы:

Похожие инструкции для VRV RXYMQ-A Series

Бренды по названию

Популярные бренды