Daikin VRV RXYMQ-A Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 305

background image

Names and Functions

SiME332106E

28

Part 3 Remote Controller

Mode Access Operation

On power-up, the message

Checking the connection. Please stand by.

will be displayed on

the remote controller screen. Then that message will disappear and the basic screen will be
displayed. To access a mode from the basic screen, refer to the figure below.
When any of the operation buttons is pressed, the backlight will come on and remains lit for
about 30 seconds. Be sure to press a button while the backlight is on (this does not apply to the

On/Off

button.)

Press

Cancel

button

for 4 seconds or more.

Press

Cancel

button

for 4 seconds or more.

Press

Menu/Enter

button once.

Press

Cancel

button once.

Press

Cancel

button once.

Press

Cancel

button once.

Basic screen

Main Menu screen

Service Settings screen

Maintenance Menu screen

Basic Screen

• Operation mode changeover
• Temperature setting
• Airflow rate
• Airflow direction
• Menu display
• Confirmation of each setting
• On
• Off
• Cancel
• Operation lamp

Main Menu

• Circulation airflow
• Airflow direction
• Individual air direction
• Quick start
• Ventilation
• Energy saving options
• Schedule
• Filter auto clean
• Maintenance information
• Configuration
• Current settings
• Clock & Calendar
• Language



The items on each menu vary

depending on the connected
models.

Service Settings Menu

• Test Operation
• Maintenance contact
• Field settings
• Demand
• Min setpoints differential
• External input interlock
• Group address
• Indoor unit AirNet address
• Outdoor unit AirNet address
• Error history
• Indoor unit status
• Outdoor unit status
• Forced fan ON
• Switch main sub controller
• Filter indicator
• Test filter auto clean
• Brush/Filter ind
• Disable filter auto clean

Maintenance Menu

• Model name
• Operation hours
• Indoor unit status
• Outdoor unit status
• Forced defrost
• Error display
• Swap unit No.
• Addressed sensor value

«
...
32
33
34
35
36
...
»

Содержание VRV RXYMQ-A Series


















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VRV RXYMQ-A Series

Бренд: KDK Страницы: 40

Бренд: Jandy Страницы: 16

Бренд: Larius Страницы: 56

Бренд: Waterous Страницы: 10

Бренд: Duraflame Страницы: 28

Бренд: Lifepro Страницы: 13

StreetHeat SR-28

Бренд: INTEGRATED PAVING CONCEPTS Страницы: 21

Бренд: Bionaire Страницы: 8

Бренд: Mr. Heater Страницы: 36

Бренд: Bryant Страницы: 54

Бренд: Vornado Страницы: 9

Pacific Hydrostar 2" or 3" Dirty Water Pump...

Бренд: Pacific hydrostar Страницы: 36

Бренд: Grundfos Страницы: 153

Бренд: Yoshitake Страницы: 6

Бренд: RainPoint Страницы: 32

CENTRI PUPPY 18510-000 Series

Бренд: JABSCO Страницы: 4

Бренд: Dru Страницы: 56

Бренд: Textron Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды