manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 402

 

10-34

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Signaling Events and Alarms

SIGNALING (62)

For additional information, refer to the 

“Received Integrated Services Digital Network RESTART 

Message—Signaling (62)” section on page 10-106

.

SIGNALING (63)

To troubleshoot and correct the cause of the alarm, refer to the 

“Media Gateway/Termination 

Faulty—Signaling (63)” section on page 10-137

.

DESCRIPTION

Received Integrated Services Digital Network RESTART Message (Received ISDN RESTART 
Message)

SEVERITY

INFO

THRESHOLD

100

THROTTLE

0

DATAWORDS

Termination Name–STRING [40]

 

Termination Index–FOUR_BYTES

 

Trunk Group ID–FOUR_BYTES

 

Trunk Group Index–FOUR_BYTES

 

Flag–FOUR_BYTES

PRIMARY

 

CAUSE

Issued when an ISDN restart message was received from the specified gateway.

PRIMARY

 

ACTION

Monitor the event reports at the network level to verify that the specified gateway and terminations are 
operating normally.

DESCRIPTION

Media Gateway/Termination Faulty 

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

Fully Qualified Name–STRING [80]

 

Type of Gateway–STRING [32]

 

Reason for Failure–STRING [80]

PRIMARY

 

CAUSE

Issued when a media gateway or termination has gone faulty due to the detection of an unknown 
endpoint, unknown package type, and unknown event, a hardware failure, or a general call agent error.

PRIMARY

 

ACTION

Verify the proper operation of the media gateway specified. Place the termination out-of-service and 
then back into service from the call agent.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды