manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 712

 

15-86

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Enhanced Traffic Measurement

ISDN_STATUS_ENQUIRY_TX

The number of ISDN STATUS ENQUIRY messages sent from the reporting call agent

ISDN_STATUS_ENQUIRY_RX

The number of ISDN STATUS ENQUIRY messages received by the reporting call 
agent

ISDN_SRVC_TX

The number of ISDN SERVICE messages sent from the reporting call agent

ISDN_SRVC_RX

The number of ISDN SERVICE messages received by the reporting call agent

ISDN_SRVC_ACK_TX

The number of ISDN SERVICE ACK messages sent from the reporting call agent

ISDN_SRVC_ACK_RX

The number of ISDN SERVICE ACK messages received by the reporting call agent

ISDN_FACILITY_TX

The number of ISDN FACILITY messages sent from the reporting call agent

ISDN_FACILITY_RX

The number of ISDN FACILITY messages received by the reporting call agent

ISDN_SUSPEND_TX

The number of ISDN Suspend messages sent from the reporting call agent. 

Note

This counter is only applicable to ETSI PRI.

ISDN_SUSPEND_RX

The number of ISDN Suspend messages received by the reporting call agent. 

Note

This counter is only applicable to ETSI PRI.

ISDN_SUSPEND_ACK_TX

The number of ISDN Suspend Acknowledge messages sent from the reporting call 
agent. 

Note

This counter is only applicable to ETSI PRI.

ISDN_SUSPEND_ACK_RX

The number of ISDN Suspend Acknowledge messages received by the reporting call 
agent. 

Note

This counter is only applicable to ETSI PRI.

ISDN_SUSPEND_REJ_TX

The number of ISDN Suspend Reject messages sent from the reporting call agent. 

Note

This counter is only applicable to ETSI PRI.

ISDN_SUSPEND_REJ_RX

The number of ISDN Suspend Reject messages received by the reporting call agent. 

Note

This counter is only applicable to ETSI PRI.

ISDN_RESUME_TX

The number of ISDN Resume messages sent from the reporting call agent. 

Note

This counter is only applicable to ETSI PRI.

ISDN_RESUME_RX

The number of ISDN Resume messages received by the reporting call agent. 

Note

This counter is only applicable to ETSI PRI.

ISDN_RESUME_ACK_TX

The number of ISDN Resume Acknowledge messages sent from the reporting call 
agent. 

Note

This counter is only applicable to ETSI PRI.

ISDN_RESUME_ACK_RX

The number of ISDN Resume Acknowledge messages received by the reporting call 
agent. 

Note

This counter is only applicable to ETSI PRI.

ISDN_RESUME_REJ_TX

The number of ISDN Resume Reject messages sent from the reporting call agent. 

Note

This counter is only applicable to ETSI PRI.

ISDN_RESUME_REJ_RX

The number of ISDN Resume Reject messages received by the reporting call agent. 

Note

This counter is only applicable to ETSI PRI.

Table 15-9

ISDN Protocol Counters (continued)

Counter Label

Counter Context

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды