Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 504 | Manualshive

Страница: 504 / 874

Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 504

10-136

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10 Signaling Troubleshooting

Troubleshooting Signaling Alarms

Destination Point Code Unavailable—Signaling (23)

The Destination Point Code Unavailable alarm (major) indicates that the specified DPC is not available.
This alarm indicates that the BTS 10200 is unable to communicate with the specified DPC in the SS7
network. Determine if the issue is a communication problem between the BTS 10200 and the IP transfer
point (ITP) or if it is related to communication problems between the ITP and the DPC by following
these steps:

Step 1

Use the BTS 10200 CLI

show alarm

command to determine if there is an active Signaling Gateway

Group Out of Service alarm. This will occur if communication has been lost to at least one of the SGs
in the SG-Group. If so, proceed to the

“Signaling Gateway Group Is Out-of-Service—Signaling (110)”

section on page 10-150

. Otherwise, proceed to Step 2.

Step 2

Determine if there is an M3UA Cannot Go Active alarm. This occurs if, at the time of startup or failover,
the BTS 10200 is not able to communicate with any of the SGs. If this is the case, proceed to the

“Message Transfer Part 3 User Adapter Cannot Go Active—Signaling (122)” section on page 10-154

Otherwise, proceed to Step 3.

Step 3

If you arrive at this step, there is probably communication between the BTS 10200 and ITP at the M3UA
and SCCP user adapter (SUA) layers, and a communication problem exists between the ITP and the
unavailable DPC. To confirm this, log on to each ITP, get into enable mode, and enter

show cs7 route

.

The output of this command tells you if the associated DPC is accessible or not from the ITP point of
view and will look similar to the following:

va-2651-82#show cs7 route

Destination Prio Linkset Name Route

---------------------- ---- ------------------- -------

229.123.2/24 INACC 1 lset1chn UNAVAIL

This output indicates that DPC 229.123.2 is unavailable from the ITP point of view.

Step 4

Determine if the problem is at the link level or at a higher level outage in the DPC by typing

show cs7

linkset

. If the ITP shows that the DPC is AVAIL, there is a mismatch between the ITP and BTS 10200.

Please contact the Cisco TAC.

Step 5

Check whether the DPC has been removed from the BTS 10200 database. At the BTS 10200 CLI prompt,
enter

show call-ctrl-route

or

show sccp-route

and see if the DPC is in any of the routes. If not, the alarm

was raised before the associated routes were deleted. If this is the case, manually clear the alarm.

Step 6

If you still cannot determine the cause of the problem, contact the Cisco TAC.

«
...
502
503
504
505
506
...
»

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды