manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 718

 

15-92

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Enhanced Traffic Measurement

CALLP_H323_CALL_ABAND

The number of terminating and originating H323 call attempts that were 
abandoned on the reporting call agent.

CALLP_ISDN_H323_CALL

The total number of successfully completed calls from an ISDN originator 
to an H323 terminator on the reporting call agent.

CALLP_SS7_H323_CALL

The total number of successfully completed calls from an SS7 originator 
to an H323 terminator on the reporting call agent.

CALLP_SIP_H323_CALL

The total number of successfully completed calls from a SIP originator to 
an H323 terminator on the reporting call agent.

CALLP_MGCP_H323_CALL

The total number of successfully completed calls from an MGCP 
originator to an H323 terminator on the reporting call agent.

CALLP_CAS_H323_CALL

The total number of successfully completed calls from a CAS originator 
to an H323 terminator on the reporting call agent.

CALLP_H323_SIP_CALL

The total number of successfully completed calls from an H323 originator 
to a SIP terminator on the reporting call agent.

CALLP_H323_ISDN_CALL

The total number of successfully completed calls from an H323 originator 
to an ISDN terminator on the reporting call agent.

CALLP_H323_SS7_CALL

The total number of successfully completed calls from an H323 originator 
to an SS7 terminator on the reporting call agent.

CALLP_H323_MGCP_CALL

The total number of successfully completed calls from an H323 originator 
to an MGCP terminator on the reporting call agent.

CALLP_H323_CAS_CALL

The total number of successfully completed calls from an H323 originator 
to a CAS terminator on the reporting call agent.

CALLP_H323_H323_CALL

The total number of successfully completed calls from an H323 originator 
to an H323 terminator on the reporting call agent.

CALLP_NAS_AUTH_SUCC

The total number of successful NAS Authentication Requests on the 
reporting call agent.

CALLP_NAS_AUTH_FAIL

The total number of failed NAS Authentication Requests on the reporting 
call agent.

CALLP_NAS_OP_FAIL

The total number of operation failures that occurred on the reporting call 
agent–typically indicative of a modem failure.

CALLP_NAS_ISP_PORT_LIMIT

The total number of NAS calls that failed on the reporting call agent due 
to the port limit of a modem being exceeded.

CALLP_NAS_NO_MODEMS

The total number of NAS calls that failed on the reporting call agent due 
to the unavailability of a modem.

CALLP_NAS_CLG_UNACC

The total number of NAS calls that failed on the reporting call agent due 
to the calling party number being blocked.

CALLP_NAS_CLD_UNACC

The total number of NAS calls that failed on the reporting call agent due 
to the called party number being blocked.

CALLP_NAS_USER_REQUEST

The total number of User Requests–Reason Code 801–that are received in 
the DLCX messages on the reporting call agent.

CALLP_NAS_LOST_CARRIER

The total number of Lost Carrier–Reason Code 802–that are received in 
the DLCX messages on the reporting call agent.

Table 15-10

Call Processing Counters (continued)

Counter Label

Counter Context

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды