manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 849

 

C-5

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Appendix C      Overload Control

Configuring

Configuring Emergency Call Handling

The BTS checks the:

  •

Called-party number for all incoming calls against the EMERGENCY-NUMBER-LIST 

  •

Calling party category (CPC) in ISUP calls

If the BTS determines it is an emergency call and the MCL is 1, 2, or 3, the BTS gives it priority and 
does not rejected the call. If the MCL is 4, The BTS rejects all calls, including emergency calls.

To add a number to the EMERGENCY-NUMBER-LIST, enter a command similar to the following:

add emergency-number-list digit_string=911;

Reply : Success: at 2006-02-28 09:48:40 by btsadmin

MNT add successful

Transaction 934823299797597704 was processed.

To display the EMERGENCY-NUMBER-LIST, enter:

show emergency-number-list;

DIGIT_STRING=911

Reply : Success: at 2006-02-28 09:48:45 by btsadmin

Entry 1 of 1 returned.

To delete a number from the EMERGENCY-NUMBER-LIST, enter a command similar to the 
following:

delete emergency-number-list digit_string=911;

Reply : Success: at 2006-02-28 09:52:20 by btsadmin

MNT delete successful

Transaction 934823480106794504 was processed.

Configuring SIP Message Handling

When processing an incoming SIP call, the BTS looks at the MCL of the CA. It uses the following 
factors to decide whether to accept or reject the message:

  •

SIP Message Type

  •

Call type (normal or emergency)

  •

Configured rejection percentage

  •

Current MCL status 

SIP Message Types

Message Rejection: INVITE

If overloaded BTS rejects a percentage of incoming INVITE messages. The percentage rejected is based 
on sia.cfg. Only new INVITE messages are checked for acceptance. Re-INVITE messages are always 
accepted. 

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды