manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 374

 

10-6

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Signaling Events and Alarms

SIGNALING (8)

To troubleshoot and correct the cause of the alarm, refer to the 

“Session Initiation Protocol Message 

Receive Failure—Signaling (8)” section on page 10-131

.

Note

Refer to the 

“Obtaining Documentation and Submitting a Service Request” section on page lvi

 for 

detailed instructions on contacting Cisco TAC and opening a service request.

SIGNALING (9)

To troubleshoot and correct the cause of the alarm, refer to the 

“Timeout on Internet Protocol 

Address—Signaling (9)” section on page 10-131

.

DESCRIPTION

Session Initiation Protocol Message Receive Failure (SIP Message Receive Failure)

SEVERITY

MAJOR

THRESHOLD

30

THROTTLE

0

DATAWORDS

Reason Text–STRING [50]

PRIMARY

 

CAUSE

Operating system level network errors have occurred or an invalid network configuration exists.

PRIMARY

 

ACTION

Have your network administrator resolve the network errors. Contact Cisco TAC if you need 
assistance. Manually clear the alarm. Restart this call agent instance using the 

platform start

 

command.

DESCRIPTION

Timeout on Internet Protocol Address (Timeout on IP Address)

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

MGW/Term Name–STRING [80]

 

Gateway Type–STRING [32]

 

Possible Cause–STRING [32]

PRIMARY

 

CAUSE

Issued when opticall is unable to communicate with a gateway.

PRIMARY

 

ACTION

Verify that the gateway is both configured for service and that it has been set in service.

SECONDARY

 

ACTION

Attempt to ping the gateway using the Internet Protocol (IP) address from the event report. If the ping 
is not successful, then diagnose the issue that prevents the address from being reached.

TERNARY

 

ACTION

Use the status media gateway (MGW) identification (ID) = xxx, where xxx is the IP address given in 
the event report. If the status is not in service (INS), then use the 

control mgw

 command to put it in 

service.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды