manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 644

 

15-18

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Troubleshooting Using Snoop

H.323 Protocol (H323) example:

10.0.0.1 is an H323 gateway. 10.0.0.129 is an H323 gatekeeper. Our goal is to monitor both Registration, 
Admissions, and Status (RAS) and H.225 messaging.

a.

First, find the RAS port number and the H.225 port number.

CLI>show h323-gw

ID=ccm3_gw1

STATUS=INS

OPER_STATUS=NF

GW_H225_PORT=1720  <----------- this port

TGN_ID=4441

SECURITY=N

H245_TUNNELING=DEFAULT

TCP_MAX_LIMIT=5

TCP_MAX_AGE=30

MAX_VOIP_CALLS=65535

HIGH_WATER_MARK=0

LOW_WATER_MARK=0

IRR_BANDWIDTH_SUPP=N

IPTOS_SIG_LOWDELAY=Y

IPTOS_SIG_THROUGHPUT=N

IPTOS_SIG_RELIABILITY=N

IPTOS_SIG_PRECEDENCE=FLASH

BRQ_SUPP=Y

ANNEXE_RETRANSMIT_TIMER=500

ANNEXE_RETRANSMIT_MULTIPLIER=2

ANNEXE_RETRANSMIT_ATTEMPTS=8

CALL_START_MODE=FAST_START

ANNEXE_SUPP=N

ANNEXR_SUPP=N

STATUS_ENQ_TIMER=4

CODEC_NEG_TIMER=200

CODEC_NEG_ATTEMPTS=4

SOURCE_BASED_ROUTING=NONE 

CLI>show h323-gw2gk

H323_GW_ID=ccm3_gw1

GK_ID=Metro-GK

PRIORITY=0

GK_IP_ADDR=10.0.0.129

GK_RAS_PORT=1719  <------------ this port

MULTICAST=N

TIME_TO_LIVE=60

# snoop -d qfe0 -o h323.cap host 10.0.0.1 and port 1720 or host 10.0.0.129 and port 

1719

b.

Use Control-C to stop the packet capture. Open the file in Ethereal and inspect.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды