manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 857

 

C-13

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Appendix C      Overload Control

Troubleshooting

CPU Load of Critical Processes—Maintenance(113)

The CPU Load of Critical Processes alarm (info) shows MCL from the CPU utilization factor crossed a 
multiple of the info_alarm_step_size in olm.cfg, "Factor Level" and "Factor MCL".  This alarm appears 
for every crossing of the info_alarm_step_size in the upper and lower direction for this factor, but it is 
required to pass the next higher or lower level before appearing again.

For additional information, refer to the 

“MAINTENANCE (113)” section on page 7-60

.

Queue Length of Critical Processes—Maintenance(114)

The Queue Length of Critical Processes alarm (info) shows MCL for defined critical process queue 
length factors crossed a multiple of the info_alarm_step_size in olm.cfg, process_name then 1 byte for 
"Factor Level" and 1 for "Factor MCL". This alarm appears for every crossing of the 
info_alarm_step_size in the upper and lower direction for this factor, but it is required to pass the next 
higher or lower level before appearing again.

For additional information, refer to the 

“MAINTENANCE (114)” section on page 7-61

.

IPC Buffer Usage Level—Maintenance(115)

The IPC Buffer Usage Level alarm (info) shows MCL for IPC buffer usage factor crossed a multiple of 
the info_alarm_step_size in olm.cfg, "Factor Level" and "Factor MCL".  This alarm is produced appears 
for every crossing of the info_alarm_step_size in the upper and lower direction for this factor, but it is 
required to pass the next higher or lower level before appearing again.

For additional information, refer to the 

“MAINTENANCE (115)” section on page 7-61

.

CA Reports the Congestion Level of FS—Maintenance(116)

CA Reports the Congestion Level of FS alarm (info) shows CA received a congestion or abatement 
notification from an FS. 

For additional information, refer to the 

“MAINTENANCE (116)” section on page 7-62

.

Logs

Use the INFO logs to get differing levels of information about the alarms:

  •

INFO1—Are included with each alarm

  •

INFO3—Prints factors feature controlled by olm.cfg shows system overview

  •

INFO4—Have extra detail

  •

INFO5—Shows exact details of the factor MCL computations

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды