Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 289

Страница: 289 / 874

7-57

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 7 Maintenance Troubleshooting

Maintenance Events and Alarms

MAINTENANCE (106)

To monitor and correct the cause of the event, refer to the

“Aggregration Device Address Resolution

Failure—Maintenance (106)” section on page 7-87

MAINTENANCE (107)

To troubleshoot and correct the cause of the alarm, refer to the

“No Heartbeat Messages Received

Through Interface From Router—Maintenance (107)” section on page 7-110

DESCRIPTION

Aggregration Device Address Resolution Failure

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

DATAWORDS

Reason Code–STRING [17]

MGW ID–STRING [33]

Reason–STRING [128]

PRIMARY

CAUSE

The auto AGGR-identification (ID) resolution for the media gateway (MGW) IP failed due to a DNS
lookup failure.

PRIMARY

ACTION

Check the provisioning of the DNS reverse lookup entry for the MGW IP address.

DESCRIPTION

No Heartbeat Messages Received Through Interface From Router (No HB Messages Received
Through Interface From Router)

SEVERITY

CRITICAL

THRESHOLD

100

THROTTLE

DATAWORDS

Interface Name–STRING [20]

Critical Local IP Address–STRING [50]

Router IP Address–STRING [50]

PRIMARY

CAUSE

The router is down.

PRIMARY

ACTION

Restore the router functionality.

SECONDARY

CAUSE

Connection to the router is down.

SECONDARY

ACTION

Restore the connection.

TERNARY

CAUSE

Network congestion.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды