manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 590

 

14-16

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 14      General Troubleshooting

Protocol Troubleshooting

Logging On to the Internet Protocol Transfer Point

Some of the troubleshooting sections in this chapter require the user to log on to the ITP. Access the ITP 
through the associated console server or through direct access with a console cable. You need the 
username and password to access the ITP. 

Troubleshooting the ITP will require you to be in ITP enable mode. The enable mode is password 
protected. To get into enable mode, after logging in to the ITP, type 

enable

. You will be prompted for 

the enable password.

Viewing the Internet Protocol Transfer Point Configuration

To view the ITP configuration, log in to the ITP and get into enable mode. Enter the command 

show 

run

. The configuration will be displayed. Continue to hit the enter key until you have viewed the entire 

configuration, or type “

q

” to stop viewing the configuration.

Internet Protocol Transfer Point Status Commands

The following ITP commands are helpful for displaying the status of ITP resources:

  •

show cs7 as—Retrieves the application server (AS) status

  •

show cs7 asp—Retrieves the application service provider (ASP) status

  •

show cs7 linkset—Retrieves the Signaling System 7 (SS7) linkset status

  •

show cs7 route—Retrieves the SS7 route status

  •

show cs7 group state—Retrieves the signaling gateway (SG) group status

Controlling Internet Protocol Transfer Point Resources

Change the administrative state of an ITP resource as follows:

Step 1

Log on to the ITP, and get into configure mode.

Step 2

Type the first configuration line of the resource that you want to control.

Step 3

Type 

shut

 to take the resource out of service, or type 

no-shut

 to place the resource back in service.

The following example takes a linkset out of service:

va-2651-33#conf t

Enter configuration commands, one per line va-2651-33(config-cs7-ls)#

va-2651-33(config)#cs7 linkset lset1 1.1.20

va-2651-33(config-cs7-ls)#shut

*May 19 12:32:13.827: %CS7MTP3-5-ACTDEACTLINKSET: Linkset lset1 deactivation is in 

progress

*May 19 12:32:13.827: %CS7MTP3-5-LINKUPDOWN: Link 0 in linkset lset1 is down

To put the linkset back in service, type the following command:

va-2651-33(config-cs7-ls)#no shut

*May 19 12:33:47.704: %CS7MTP3-5-ACTDEACTLINKSET: Linkset lset1 activation is in progress

*May 19 12:33:47.704: %CS7MTP3-5-ACTDEACTLINK: Link 0 linkset lset1 activation is in 

progress

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды