manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 364

 

9-4

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 9      Security Troubleshooting

Security Events and Alarms

SECURITY (5)

To monitor and correct the cause of the event, refer to the 

“Internet Protocol Security Outgoing Security 

Association Not Found—Security (5)” section on page 9-6

.

SECURITY (6)

To monitor and correct the cause of the event, refer to the 

“Secure Session Initiation Protocol Endpoint 

Validation Failure—Security (6)” section on page 9-6

.

DESCRIPTION

Internet Protocol Security Outgoing Security Association Not Found (IPSEC Outgoing SA Not Found)

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

PRIMARY

 

CAUSE

The KMS receives SA-missing messages from the IPSEC engine and is unable to find a provisioned 
device to establish the needed security association (SA).

PRIMARY

 

ACTION

Remove or modify the security policy which caused the SA not found error. This action assumes that 
security is provisioned.

DESCRIPTION

Secure Session Initiation Protocol Endpoint Validation Failure (Secure SIP Endpoint Validation 
Failure)

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

DATAWORDS

AOR–STRING [65]

 

Secure Fqdn–STRING [65]

 

Source IP Address–STRING [16]

 

Violation Description–STRING [80]

PRIMARY

 

CAUSE

There is erroneous provisioning in the BTS 10200.

PRIMARY

 

ACTION

Check if correct value of Secure-FQDN is provisioned in the BTS 10200.

SECONDARY

 

CAUSE

There is erroneous provisioning in the domain name system (DNS).

SECONDARY

 

ACTION

Verify the resolution of the Secure-FQDN in the DNS.

TERNARY

 

CAUSE

There is erroneous provisioning in the customer premises equipment (CPE).

TERNARY

 

ACTION

Verify the CPE provisioning to ensure that the correct source Internet Protocol (IP)/contact is used.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды