manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 760

 

16-12

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 16      Disaster Recovery Procedures

Element Management System Database Recovery from Hot Backup

Recovering the Primary Element Management System Database

Perform the following procedure on the primary EMS system to recover the primary EMS database from 
your most recent backup files:

Step 1

Make sure the platform is shut down and the system cron process has stopped.

Step 2

Log in as 

root

.

Step 3

Enter the following commands to shut down the system:

platform stop all

svcadm disable svc:/system/cron

Note

Execute 

platform stop all

 and 

stop_cron.sh

 on the secondary EMS also if the secondary EMS 

platform is active.

Step 4

Log in as 

oracle

 user, or 

su – oracle.

Step 5

Enter the following command to verify that there is enough free disk space:

df –k /opt/oraback

The EMS system must have enough disk space in the 

/opt/oraback

 directory to restore all database data 

files and archive log files. The database data files can take up to 3.6 gigabits (GB) if it is fully populated 
with data; each archivelog file requires 5MB additional space. The number of archivelog files in the 
backup set can be identified from the optical1_ora_hot_full_backup_<timestamp>.log and/or the 
optical1_ora_arc_incr_backup_<timestamp>.log file in 

/opt/oraback

 directory.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды