Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 717

Страница: 717 / 874

15-91

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15 Diagnostic Tests

Enhanced Traffic Measurement

CALLP_INTRALA_FAIL

The number of Intralata call attempts that failed on the reporting call
agent.

CALLP_INTRALA_SUCC

The number of Intralata call attempts that completed successfully on the
reporting call agent.

CALLP_INTRALA_ABAND

The number of Intralata call origination attempts that were abandoned on
the reporting call agent.

CALLP_INTL_ATTMP

The number of International call attempts on the reporting call agent.

CALLP_INTL_FAIL

The number of International call attempts that failed on the reporting call
agent.

CALLP_INTL_SUCC

The number of International call attempts that completed successfully on
the reporting call agent.

CALLP_INTL_ABAND

The number of International call origination attempts that were abandoned
on the reporting call agent.

CALLP_EMGNCY_ATTMP

The number of Emergency call attempts on the reporting call agent.

CALLP_EMGNCY_FAIL

The number of Emergency call attempts that failed on the reporting call
agent.

CALLP_EMGNCY_CALL_SUCC

The number of Emergency call attempts that completed successfully on
the reporting call agent.

CALLP_EMGNCY_CALL_ABAND

The number of Emergency call origination attempts that were abandoned
on the reporting call agent.

CALLP_LOCAL_ATTMP

The number of Local call attempts on the reporting call agent.

CALLP_LOCAL_FAIL

The number of Local call attempts that failed on the reporting call agent.

CALLP_LOCAL_SUCC

The number of Local call attempts that completed successfully on the
reporting call agent.

CALLP_LOCAL_ABAND

The number of Local call origination attempts that were abandoned on the
reporting call agent.

CALLP_TOLL_FREE_ATTMP

The number of Toll Free call attempts on the reporting call agent.

CALLP_TOLL_FREE_FAIL

The number of Toll Free call attempts that failed on the reporting call
agent.

CALLP_TOLL_FREE_SUCC

The number of Toll Free call attempts that completed successfully on the
reporting call agent.

CALLP_TOLL_FREE_ABAND

The number of Toll Free call origination attempts that were abandoned on
the reporting call agent.

CALLP_H323_ORIG_ATTMP

The number of originating H323 call attempts on the reporting call agent.

CALLP_H323_TERM_ATTMP

The number of terminating H323 call attempts on the reporting call agent.

CALLP_H323_ORIG_FAIL

The number of originating H323 call attempts that failed on the reporting
call agent.

CALLP_H323_TERM_FAIL

The number of terminating H323 call attempts that failed on the reporting
call agent.

CALLP_H323_CALL_SUCC

The number of originating and terminating H323 call attempts that
completed successfully on the reporting call agent.

Table 15-10

Call Processing Counters (continued)

Counter Label

Counter Context

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды