manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 816

 

B-8

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Appendix B      System Usage of MGW Keepalive Parameters, Release 5.0

Keepalive for Release 5.0 Prior to Maintenance Release 1.1

MGCP-MAX2-RETRIES, MGCP-T-MAX and 2*MGCP-T-HIST

The BTS 10200 limits retransmissions of the AUEP message to 

mgcp-max2-retries

 or a total duration 

of 

mgcp-t-max

 (default = 20 seconds), whichever occurs first. 

If the system does not receive an ACK before the expiration of

 2*mgcp-t-hist

 (two times the provisioned 

value for mgcp-t-hist), it abandons the transaction and takes 

one

 of the following additional actions:

  •

If keepalive functionality is 

enabled

 on the system (

mgw-monitoring-enabled=Y

 and 

keepalive-method=AUEP

 as described in the 

“Provisionable Parameters” section on page B-2

), the 

system expedites the KA process (as described in the 

“Keepalive Process” section on page B-9

) 

without immediately declaring the termination to be unreachable. However, if the KA process also 
fails, the system declares the MGW and all associated terminations to be unreachable. The 
operational status of each of the terminations is marked as TERM_UNREACH.

  •

If keepalive functionality is 

disabled

 on the system, the system marks the operational status of each 

of the terminations as UNKNOWN.

Figure B-4

 shows how the system handles AUEP retransmissions and takes action if no ACK is received. 

In this example, mgcp-max2-keepalive attempts are completed before the expiration of mgcp-t-max. In 
general, the system stops retransmissions when mgcp-max2-keepalive attempts are completed or at the 
expiration of mgcp-t-max, whichever occurs first.

Figure B-4

Timeout Limitations When No ACK Is Received

mgcp-t-max (default = 20 seconds)

Maximum time allowed for retransmissions.

2 * mgcp-t-hist

BT

S

 10200 declares endpoint unreachable

after this time if no ACK received.

(No additional 
retransmissions sent)

mgcp-max1-retries (default = 2)
Maximum number of AUEP
retransmissions sent to each
IP address of the MGW.

mgcp-max2-retries (default = 

3

)

Maximum number of AUEP
retransmissions sent to the
last IP address of the MGW.

25002

3

Time

mgcp-t-tran

2*mgcp-t-tran

4*mgcp-t-tran

8

*mgcp-t-tran

KA attempt

(AUEP transaction)

AUEP, 
initial 
transmission

16*mgcp-t-tran

AUEP,
2nd transmission
(1st retransmission) 

AUEP,

3

rd transmission

(2nd retransmission) 

AUEP,
4th transmission
(

3

rd retransmission) 

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды