manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 455

 

10-87

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Signaling Events and Alarms

SIGNALING (167)

To monitor and correct the cause of the event, refer to the 

“No Signaling Gateways are 

Active—Signaling (167)” section on page 124

.

SIGNALING (168)

To monitor and correct the cause of the event, refer to the 

“A Session Initiation Protocol Server Group 

has no Child Elements Provisioned—Signaling (168)” section on page 124

.

DESCRIPTION

No Signaling Gateways are Active

SEVERITY

WARNING

THRESHOLD

0

THROTTLE

0

PRIMARY

 

CAUSE

A communication problem between the ITP and the BTS 10200 has occurred.

PRIMARY

 

ACTION

Check the communication path between the BTS 10200 and the ITP.

DESCRIPTION

A Session Initiation Protocol Server Group has no Child Elements Provisioned (A SIP Server Group 
has no Child Elements Provisioned)

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

DATAWORDS

Server Group ID–STRING [64]

PRIMARY

 

CAUSE

Issued when a SIP Server Group administrative in-service is provisioned but has no child elements 
provisioned.

PRIMARY

 

ACTION

This Server Group will be considered as if it is administrative out of service. If that is acceptable, then 
no action required. If the server group was expected to be workable, then place the server group back 
out of service, resolve the provisioning problem, and place back into service.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды