Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 721

Страница: 721 / 874

15-95

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15 Diagnostic Tests

Enhanced Traffic Measurement

MGCP Adapter Counters

Table 15-11

identifies the MGCP Adapter counters provided in Release 4.5.

Table 15-11

MGCP Adapter Counters

Counter Label

Counter Context

MGCP_DECODE_ERROR

The number of MGCP messages received that failed decoding on the reporting call agent.

MGCP_ENCODE_ERROR

The number of MGCP messages to be sent that failed encoding on the reporting call agent.

MGCP_UNREACHABLE

The number of MGCP messages sent from the reporting call agent that failed due to the
target gateway being unreachable.

MGCP_SEND_FAILED

The number of MGCP messages sent from the reporting call agent that failed while being
sent to the target gateway.

MGCP_CRCX_ACK_RX

The number of MGCP CRCX acknowledgement messages received by the reporting call
agent.

MGCP_CRCX_NACK_RX

The number of MGCP CRCX non-acknowledgement messages received by the reporting call
agent.

MGCP_CRCX_TX

The number of MGCP CRCX messages sent by the reporting call agent.

MGCP_MDCX_ACK_RX

The number of MGCP MDCX acknowledgement messages received by the reporting call
agent.

MGCP_MDCX_NACK_RX

The number of MGCP MDCX non-acknowledgement messages received by the reporting
call agent.

MGCP_MDCX_TX

The number of MGCP MDCX messages sent by the reporting call agent.

MGCP_DLCX_RX

The number of MGCP DLCX messages received from gateways by the reporting call agent.

MGCP_DLCX_TX

The number of MGCP DLCX messages s.ent by the reporting call agent

MGCP_DLCX_ACK_RX

The number of MGCP DLCX acknowledgement messages received by the reporting call
agent.

MGCP_DLCX_NACK_RX

The number of MGCP DLCX non-acknowledgement messages received by the reporting call
agent.

MGCP_RQNT_ACK_RX

The number of MGCP RQNT acknowledgement messages received by the reporting call
agent.

MGCP_RQNT_NACK_RX

The number of MGCP RQNT non-acknowledgement messages received by the reporting call
agent.

MGCP_RQNT_TX

The number of MGCP RQNT messages sent by the reporting call agent.

MGCP_AUEP_ACK_RX

The number of MGCP AUEP acknowledgement messages received by the reporting call
agent.

MGCP_AUEP_NACK_RX

The number of MGCP AUEP non-acknowledgement messages received by the reporting call
agent.

MGCP_AUEP_TX

The number of MGCP AUEP messages sent by the reporting call agent.

MGCP_NTFY_RX

The number of MGCP NTFY messages received from gateways by the reporting call agent.

MGCP_RSIP_RX

The number of MGCP RSIP messages received from gateways by the reporting call agent.

MGCP_RSIP_ACK_TX

The number of MGCP RSIP acknowledgement messages sent by the reporting call agent.

MGCP_AUCX_TX

The number of AUCX (Audit Connection) messages that were sent by the reporting call
agent. (FUTURE–R5.0).

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды