manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 677

 

15-51

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Session Initiation Protocol Subscriber Registration Status Check

Session Initiation Protocol Subscriber Registration Status 
Check

The SIP subscriber registration status check CLI command (sip-reg-contact) is used to check the 
registration status of a SIP subscriber. The need to check the registration status of a SIP subscriber may 
arise, for example, when a subscriber complains about not being able to receive calls. The first item to 
check would be the registration status using the sip-reg-contact CLI command. The next item would be 
to check for events regarding authentication failures and etc.

The following examples show the usage of the sip-reg-contact CLI command. The first example provides 
an example of a expired contact and the second example provides an example of a registered contact or 
current contact.

Example 1:

CLI to check the registration status of an address of record (AOR).

CLI>status sip-reg-contact;

CLI>[email protected];

AOR ID -> [email protected]

USER -> 4692551119

HOST -> 10.89.220.21

PORT -> 5060

USER TYPE ->  USER_PHONE_TYPE

EXPIRES -> 3600

EXPIRETIME -> Tue Oct  7 12:13:11 2003

STATUS -> EXPIRED CONTACT

Reply : Success:

Example 2:

CLI to check the registration status of an AOR.

CLI>status sip-reg-contact;

CLI>[email protected];

AOR ID -> [email protected]

USER -> 4692551001

HOST -> 10.89.223.193

PORT -> 5060

USER TYPE -> USER_IP_TYPE

EXPIRES -> 3600

EXPIRETIME -> Thu Oct 23 16:23:48 2003

STATUS -> REGISTERED CONTACT

Reply : Success:

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды