manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 777

 

16-29

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 16      Disaster Recovery Procedures

Recovering Shared Memory Data

Recovering Shared Memory Data

The 

download database 

command refreshes data in the Call Agent (CA) shared memory. In the event 

that shared memory data cannot be recovered, it recovers data in the CA shared memory. The 

download 

database 

command

 

wipes out Call Agent shared memory data and causes a total outage.

Caution

Read this section in its entirety before attempting this procedure.

 

 

Do not use this command on 

any

 live traffic production systems. Contact Cisco TAC regarding the use 

of this command for disaster recovery.

Caution

Do not

 

download the database through the console port because the TTY can cause long delays.

 

 

Downloads of the CA, FSAIN and FSPTC applications can be done in parallel.

You can perform the 

download database 

command by ID. The 

download by ID

 command allows you 

to copy database information from the EMS to a specific CA or Feature Server (FS). If a CA ID is not 
specified, the command copies to all IDs.

Use one of the following examples to download database by ID. 

download database target=ca; id=CAxxx

download database target=fsptc; id=FSPTCxxx

download database target= fsain; id=FSAINxxx

See the 

BTS 10200 Command Line Interface Reference Guide

 for table and token descriptions.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды