manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 637

 

15-11

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Channel-Associated Signaling Trunk Termination Tests

Channel-Associated Signaling Trunk Termination Tests

This section describes the tests that can be performed on channel-associated signaling (CAS) trunk 
terminations. All terminations must be in the MAINT state for testing.

Step 1

Force the CAS trunk termination into MAINT state:

control cas-trunk-termination tgn-id=64; mode=forced; target-state=maint;

Step 2

Display the Test Menu.

diag cas-trunk-termination

Reply Example:

Reply: Diagnostic CAS Trunk Group Menu.

===

(1) CAS MGCP Connectivity Test

(2) CAS Termination Connection Test

(3) ALL

Note

Test #1 tests if MGCP has access to the CAS termination. 

 

Test #2 tests if there is a path to the device (ping). 

 

Test #3 performs tests 1 and 2.

Step 3

To perform a specific test, use the following examples as a guide:

diag cas-trunk-termination tgn-id=64;cic=1;test=1;

Reply Example:

TRUNK DIAGNOSTIC TEST EXECUTED -> diag trunk

TG-NUM -> 64

CIC -> 1

TEST-TYPE -> ADM-MGW-MGCP-CONNECTIVITY-TEST

TEST-DURATION -> 0

RESULT -> TEST-SUCCESS

REASON -> PASSED: Reason: AUEP-NACK received with RespCode = 510

Reply: Diagnostic command executed.

diag cas-trunk-termination tgn-id=64;cic=1;test=2;

Reply Example:

TRUNK DIAGNOSTIC TEST EXECUTED -> diag trunk

TG-NUM -> 64

CIC -> 1

TEST-TYPE -> ADM-TERM-CONNECTION-TEST

TEST-DURATION -> 32

RESULT -> TEST-SUCCESS

REASON -> PASS successfully.

Reply: Diagnostic command executed.

diag cas-trunk-termination tgn-id=64;cic=1;test=3;

Reply Example:

TRUNK DIAGNOSTIC TEST EXECUTED -> diag trunk

TG-NUM -> 64

CIC -> 1

TEST-TYPE -> ADM-MGW-MGCP-CONNECTIVITY-TEST

TEST-DURATION -> 11

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды