manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 611

 

14-37

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 14      General Troubleshooting

Protocol Troubleshooting

Trunk Static State Is Set to Remote Block

Perform the following steps if trunk static state is set to remote block (RBLK). 

Note

If the trunk static state is set to RBLK, and isdn-tg-profile has isdn-farend-init=Y then the PBX must 
start the initialization procedure, or the PBX specifically sends a service message with SERVICE-OOS 
mode to the BTS 10200 to put the trunks into the remote out-of-state mode.

Step 1

Verify that the initialization procedure (ISDN-FAREND-Initialize (INIT) token), as depicted by 
associated isdn-tg-profile in the BTS 10200, and as used by the PBX, is in sync.

Step 2

Using the CLI command “control trunk-termination” to reset the RBLK state, perform a control 
trunk-termination to OOS, then control trunk-termination to INS—in case there is an error on the PBX 
side. Also, set the isdn-service-supp token in the ISDN trunk group profile per the procedures supported 
by the PBX.

Termination Status Is Faulty 

The 

TERM_STATUS_FAULTY message 

indicates an MGCP problem.

Things to Check:

  •

Is the media gateway (MGW) profile set up for the trunk?

  •

Is the MGW in the in-service operational state?

Perform the “no mgcp, mgcp” commands on the gateway if an MGCP problem is indicated.

Cannot Make a Call

If you have a problem making a call, perform the following Things to Check, and then go to the 

“Checking Media Gateway Provisioning” section on page 14-38

Things to Check:

When terminations are added, they have strings like S0/DS1-2/1. The S# refers to the slot number. The 
DS1-# refers to the port number. The /# at the end refers to the specific B channel (1–23). The slot and 
port numbers must match the dchan values (dchan-slot, dchan-port) for the related trunk group ID 
(tgn-ID), assuming that the DS0 is on a T1 that contains a D channel.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды