manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 109

 

3-3

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 3      Billing Troubleshooting

Billing Events and Alarms

BILLING (1)

For additional information, refer to the 

“Test Report—Billing (1)” section on page 3-27

.

BILLING (2)

To troubleshoot and correct the cause of the alarm, refer to the 

“Billing Partition Disk Usage Minor 

Threshold Exceeded—Billing (2)” section on page 3-35

.

DESCRIPTION

Test Report

SEVERITY

Information (INFO)

THRESHOLD

10000

THROTTLE

0

DESCRIPTION

Billing Partition Disk Usage Minor Threshold Exceeded

SEVERITY

MINOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

Disk Usage Percentage–TWO_BYTES 

PRIMARY

 

CAUSE

Call detail records are accumulating on the disk associated with the billing database in the Element 
Management System (EMS). This is because data is being written into the database faster than it is 
being read out of the database. The minor threshold (default value = 70%) has been exceeded. 

PRIMARY

 

ACTION

Monitor this alarm. The read process should catch up to write process within a few minutes, and the 
alarm should not remain active.

SECONDARY

 

CAUSE

Some fluctuation in disk usage is to be expected as the call volume rises and falls during the day. 
Threshold crossings might step upward (from MINOR to MAJOR to CRITICAL) when there is a rapid 
increase in the call volume, and then step downward (CRITICAL to MAJOR to MINOR) when the call 
volume slows.

SECONDARY

 

ACTION

To monitor the alarm, use the 

subscribe alarm-report

 command. To obtain a summary, use the 

report 

alarm-summary

 command. Verify that type = billing is entered in the commands. 

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды