manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 154

 

4-4

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 4      Call Processing Troubleshooting

Call Processing Events and Alarms

CALLP (8)

To monitor and correct the cause of the event, refer to the 

“No Route Available for Called Number—Call 

Processing (8)” section on page 4-24

.

DESCRIPTION

No Route Available for Called Number

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

500

DATAWORDS

Orig Type (Trunk or S–ONE_BYTE

 

Orig Sub or TG ID–EIGHT_BYTES

 

Calling Party Number–STRING [20]

 

Called Party Number–STRING [20]

PRIMARY

 

CAUSE

The call originated from a subscriber or trunk for a called party number that has no route available.

PRIMARY

 

ACTION

The data words in the event report indicate what parameters that need to be corrected. Refer to the 
office records for the subscriber.

SECONDARY

 

CAUSE

Parameter(s) in the subscriber and/or dial-plan table are missing or incorrect for the dialed number.

SECONDARY

 

ACTION

Determine whether the routing parameters (such as digit-string) were entered correctly in the 
subscriber and dial-plan tables.

TERNARY

 

ACTION

If the called party is a subscriber, verify that the subscriber-type is listed as subscriber in the dial-plan 
table.

SUBSEQUENT

 

ACTION

If the call is long distance using a presubscribed interexchange carrier (PIC), check that the PIC for 
this subscriber is properly provisioned in the dial-plan table. If necessary, edit these files using the 

change dial-plan

 or 

change subscriber

 commands.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды