manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 382

 

10-14

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Signaling Events and Alarms

SIGNALING (24)

To troubleshoot and correct the cause of the alarm, refer to the 

“Destination Point Code 

Congested—Signaling (24)” section on page 10-137

.

SIGNALING (25)

To monitor and correct the cause of the event, refer to the 

“Unanswered Blocking Message—Signaling 

(25)” section on page 10-101

.

DESCRIPTION

Destination Point Code Congested (DPC Congested)

SEVERITY

MINOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

DPC–STRING [12]

 

DPC Type–ONE_BYTE

 

Congestion Level–ONE_BYTE

PRIMARY

 

CAUSE

Issued when the specified destination point code is congested.

PRIMARY

 

ACTION

Monitor the event reports at the network level to determine if the traffic load to the specified DPC is 
too high on the local end, or if the remote end is lagging in processing the traffic.

DESCRIPTION

Unanswered Blocking Message (Unanswered BLO)

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

DATAWORDS

CIC Number–TWO_BYTES

 

TGN-ID–FOUR_BYTES

 

DPC–STRING [20]

 

OPC–STRING [20]

PRIMARY

 

CAUSE

Issued when a blocking (BLO) message was not acknowledged before the timer 13 (T13) expired for 
the associated circuit identification code (CIC).

PRIMARY

 

ACTION

Verify that the SS7 signaling adapter processes is running normally. Verify that the call agent platform 
is active.

SECONDARY

 

ACTION

Verify that the SS7 interface hardware is in service. Verify that the associated SS7 signaling link is 
available.

TERNARY

 

ACTION

Verify that the T13 timer is set to an appropriate level.

SUBSEQUENT

 

ACTION

Verify that the SS7 link is not congested.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды