manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 474

 

10-106

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Monitoring Signaling Events

Auto State Change for Integrated Services Digital Network Trunk Group by 
Media Gateway—Signaling (59)

The Auto State Change for Integrated Services Digital Network Trunk Group by Media Gateway alarm 
(major) indicates that specified ISDN trunk group status was changed due to a media gateway operation. 
To troubleshoot and correct the cause of the Auto State Change for Integrated Services Digital Network 
Trunk Group by Media Gateway alarm, refer to the 

“Auto State Change for Integrated Services Digital 

Network Trunk Group by Media Gateway—Signaling (59)” section on page 10-137

.

Integrated Services Digital Network STATUS Message Containing Error 
Indication Received—Signaling (60)

The Integrated Services Digital Network STATUS Message Containing Error Indication Received event 
functions as a warning that an ISDN status message containing an error indication has been received. 
The primary cause of the event is that an ISDN status message was received containing an error 
indication for the specified termination. To correct the primary cause of the event, place the specified 
termination in service state if the specified termination is not operating normally.

Trunk Operational State Changed by Service Message—Signaling (61)

The Trunk Operational State Changed by Service Message event functions as an informational alert that 
the trunk operational state was changed by a service message. The primary cause of the event is that the 
specified trunk group operational status was changed via a service message from the specified gateway. 
To correct the primary cause of the event, monitor the event reports at the network level to verify that 
the specified gateway and terminations are operating normally.

Received Integrated Services Digital Network RESTART Message—Signaling 
(62)

The Received Integrated Services Digital Network RESTART Message event functions as an 
informational alert that a ISDN restart message was received. The primary cause of the event is that an 
ISDN restart message was received from the specified gateway. To correct the primary cause of the 
event, monitor the event reports at the network level to verify that the specified gateway and 
terminations are operating normally.

Media Gateway/Termination Faulty—Signaling (63)

The Media Gateway/Termination Faulty alarm (major) indicates that a media gateway or termination has 
gone faulty due to the detection of an unknown endpoint, unknown package type, and unknown event, 
a hardware failure, or a general call agent error. To troubleshoot and correct the cause of the Media 
Gateway/Termination Faulty alarm, refer to the 

“Media Gateway/Termination Faulty—Signaling (63)” 

section on page 10-137

.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды