manualshive.com logo in svg

Xerox WORKCENTRE 5755, System Administrator Manual

Share
Download
Xerox WORKCENTRE 5755 System Administrator Manual Download Page 16

Device Connection and Quick Setup

Xerox WorkCentre 5735/5740/5745/5755/5765/5775/5790
System Administrator Guide

8

Initial Connection

Follow these steps to physically connect your device to the network.

1.

Connect the Power Cable
Ensure the device is connected to a suitable power supply and that the power cord is fully plugged 
in to the electrical outlet.

2.

Connect the Ethernet Cable
Connect a 10/100/1000 BaseT Ethernet cable to the Ethernet port at the rear of the device and 
the other end of the cable to your network port.

3.

Power On the Device
The Power On button is located on the left-side of the device.

Power Management

Power On/Off Button and Energy Saver Button

The 

Power On/Off

 button (located on the left hand side of the device) and the 

Energy Saver

 button 

(located on the control panel on the top left) controls the application of standby operating power to 
each of the system modules and initiates the sequences required to bring the device to an operational 
state. If the button is pressed when the device is operational, the following can be initiated:

•

Energy Saver 

- ends the current session and keeps the device running on low power. When in 

Energy Saver Mode, press any key or touch the screen to wake the device up.

•

Quick Restart

 - the system powers down followed by an automatically initiated Power On 

sequence. Any jobs in progress will be lost. Quick Restart may be helpful if experiencing problems 
with the operation of the device.

•

Power Down

 - the system ends the current session and powers itself off in an orderly manner.

Power On

At the Device:

1.

Ensure that your device is connected to a suitable power supply and that the power cord is fully 
plugged in to the electrical outlet of the device.

2.

Press the 

<Power On/Off>

 button. The entire powering on process (to power on all installed 

options) takes less than three minutes.

Power Down

At the Device:

1.

Press the 

<Power On/Off>

 button, the 

Power Down Options

 screen displays.

2.

Touch 

[Power Down]

.

3.

The 

Power Down Confirmation

 screen displays.

Note:

If the are any jobs in the queue, confirming power down will result in the deletion of any 

currently in the queue.

Summary of Contents for WORKCENTRE 5755





































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands