Siemens SIMATIC NET Page 310 Configuration Manual Download

Page: 310 / 464

Network protocols

7.3 DHCP server

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

310

Configuration Manual, 10/2015, C79000-G8976-C351-05

7.3.2.5

ip dhcp-server pool

Note
The command is only available with the following device:

•

SCALANCE W722-1 RJ-45 (MLFB 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-0AB0

(US version))

•

SCALANCE W761-1 RJ45 in access point mode (article number): 6GK5761-1FC00-0AA0

and 6GK5761-1FC00-0AB0 (US version))

Description

With this command, you have three options of changing to the DHCPPOOL configuration

mode and to assign an interface to the IPv4 address band.
1.

If you call the

ip dhcp-server pool

command without parameters, and IPv4 address band

with the next free pool ID is created and you change directly to the corresponding

DHCPPOOL configuration mode.
You then configure the interface and the other settings in the DHCPPOOL configuration

mode.

If you call the command

ip dhcp-server pool

with the parameter

pool-id (1-5)

, you

change to the corresponding DHCPPOOL configuration mode.

If you call the command

ip dhcp-server pool

with the parameter

show-interface-options

you call a variant of the command. With this variant, you assign an interface to the IPv4

address band and change to the DHCPPOOL configuration mode. If the ID of the

address IPv4 address band does not yet exist, it will be created. You then configure the

other settings in the DHCPPOOL configuration mode.

Requirement

You are in the Global Configuration mode.
The command prompt is as follows:

cli(config)#

Syntax

Call up the command with the following parameters:

ip dhcp-server pool { <pool-id (1-5)> | show-interface-options }

The parameters have the following meaning:

Parameter

Description

Range of values / note

pool-id

ID of the addressed IPv4

address band

1 ... 5
Only ID = 1 is supported.

show-interface-options

Displays the possible

options for the interface.

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands