manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Security and authentication 

 

10.2 WLAN 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

390

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

Result  

The settings are displayed.  

See also 

wlan security ap-radius-authenticator (Page 391) 
wlan security ap-radius-authenticator address (Page 393) 
wlan security ap-radius-authenticator max-retransmit (Page 394) 
wlan security ap-radius-authenticator port-number (Page 395) 
wlan security ap-radius-authenticator primary (Page 396) 
no wlan security ap-radius-authenticator primary (Page 397) 
wlan security ap-radius-authenticator reauth-interval (Page 398) 
wlan security ap-radius-authenticator reauth-mode (Page 399) 
wlan security ap-radius-authenticator shared-secret (Page 400) 

10.2.1.3

 

show wlan security keys 

Description  

This command shows a table with the WEP key of the SCALANCE W700 device.  

Requirement 

You are in the User EXEC mode or in the Privileged EXEC mode. 
The command prompt is as follows: 

cli>

 or 

cli#

 

Syntax 

Call up the command with the following parameters: 

show wlan security-keys < wlan 0/X > 

 

The parameters have the following meaning: 

 

Parameter 

Description 

Range of values / note 

wlan 0/X

 

WLAN interface 

Enter a valid interface. 

For information on identifiers of addresses and interfaces, refer to the section "Interface 

identifiers and addresses (Page 25)". 

Result  

The key table is displayed. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Kathrein UHF-ANTENNEN OLYMPIA AOI 65 User Manual preview
UHF-ANTENNEN OLYMPIA AOI 65
Brand: Kathrein Pages: 12
AXIOMTEK OPS882 NFC Quick Installation Manual preview
OPS882 NFC
Brand: AXIOMTEK Pages: 2
HiBoost C27-5S-BTW User Manual preview
C27-5S-BTW
Brand: HiBoost Pages: 15
RF Elements StarterDish 21 UM Manual preview
StarterDish 21 UM
Brand: RF Elements Pages: 19
DX Engineering DXE-ATK65A Manual preview
DXE-ATK65A
Brand: DX Engineering Pages: 8
Q-Mac TA-90 Technical Manual preview
TA-90
Brand: Q-Mac Pages: 21
Federal Signal Corporation YAGI-1 Installation Manual preview
YAGI-1
Brand: Federal Signal Corporation Pages: 18
Mohu Leaf 50 Instruction Manual preview
Leaf 50
Brand: Mohu Pages: 9
Airspan ProST User Manual preview
ProST
Brand: Airspan Pages: 71
CUSHCRAFT A270-10S Assembly And Installation Manual preview
A270-10S
Brand: CUSHCRAFT Pages: 8
WiMo Bridgepoynt Manual preview
Bridgepoynt
Brand: WiMo Pages: 4
EARDATEK KINGSAT Z3 Quick Installation preview
KINGSAT Z3
Brand: EARDATEK Pages: 21
One for All SV-9311 Instruction Manual preview
SV-9311
Brand: One for All Pages: 2
One for All 16472 Quick Installation Manual preview
16472
Brand: One for All Pages: 2
Winegard Rayzar.Air RVRZ25B User Manual preview
Rayzar.Air RVRZ25B
Brand: Winegard Pages: 12
CUSHCRAFT ringo ranger II ARX-450BN User Manual preview
ringo ranger II ARX-450BN
Brand: CUSHCRAFT Pages: 4
CUSHCRAFT LFA-2M9EL Instruction Manual preview
LFA-2M9EL
Brand: CUSHCRAFT Pages: 12
Aerohive Networks Aerohive AP141 Hardware Reference Manual preview
Aerohive AP141
Brand: Aerohive Networks Pages: 111

Brands by name

Popular brands

Load more brands